page
10
Owner’s Manual
HPC-3000 / WPC-4000 /HPC-5000 / WPC-7000 / WPC-9000 / WPC-15000
ASSEMBLY(WPC-7000,9000)
Cool air outlet hose
Front and Right Side View
Display / Control board
Top fan exhaust flange
Evaporator / filter
Guide bar for condensate water tank
Condensate water tank (Water level is
sensed, and the unit operaon is stopped
when tank is full. An alarm will be
displayed. Empty the tank and replace to
resume operaon)
Figure 21
Figure 20
Figure 22
Figure 24
Back and Le Side View
Condenser / filter
Power cord holder
Caster
Electrical access
panel
Figure 23
Figure 25
1. Remove cool air outlet hose(s) from
carton.
2. Place the cool air outlet hose(s) on
the front top of air condioner.
3. Use screws (enclosed inside of box
with cool air outlet hose(s) to install
the cool air outlet hose(s) on the air
condioner as shown in Figure 24.
An ambient air adapter can be
purchased separately. Air adapter fits
over the condenser to duct
condenser air to the unit to improve
cooling efficiency.
1. Remove air adapter from carton.
2. Place air adapter on the side of air
condioner.
3. Use screws (enclosed inside of box
with air adapter) to install the
adapter on the air condioner as
shown in Figure 25.
1. Take out the cord holder from
the accessory box.
2. Place the cord holder on the
back side of air condioner.
3. Use screws (enclosed inside of
accessory box with cord holder)
to install the cord holder on the
air condioner as shown in
Figure 22.
1. Remove the top fan exhaust
flange from carton.
2. Place the top fan exhaust flange
on the top of air condioner.
3. Use screws (enclosed inside of
box with the top fan exhaust
flange) to install the top fan
exhaust flange on air condioner
as shown in Figure 23.
Component Parts
POWER CORD HOLDER
TOP FAN EXHAUST FLANGE
DISCHARGE DUCTS
/SUPPLY AIR DUCT
AMBIENT AIR ADAPTER
(Oponal)
Figure 18
Figure 19
Figure 14 – Rear and Le Side View
Rubber stoppers
Condenser / filter
Power cord holder
Casters
Electrical
access panel
Cool air outlet hose
Display / Control board
Top fan wire grille
Guide bar for
condensate
water tank
Figure 13 – Front and Right Side View
Evaporator / filter
Condensate water tank
(Water level is sensed, and
the unit operaon is
stopped when tank is full.
An alarm will be displayed.
Empty the tank and
replace to resume
operaon)
Figure 15 – Power Cord Holder aachment
1. Remove the power cord
holder from the accessory
pack.
2. Place the power cord
holder on the rear of the
unit as shown in Figure 15.
3. Use screws to install the
power cord holder to the
rear of the unit (screws
inside the accessory pack).
1. Remove the rubber stoppers
from the accessory pack.
2. Place the rubber stoppers on
the rear of the unit as shown in
Figure 16.
3. Use screws to install the
rubber stoppers to the rear of
the unit (screws inside the
accessory pack).
Figure 16 – Rubber Stopper aachment
An exhaust flange can be purchased
separately. Exhaust flange fits over the top
exhaust fan duct improving cooling
efficiency, allowing hot air to be exhausted
to another locaon.
1. Remove exhaust flange from carton.
2. Place exhaust flange on the top of air
condioner.
3. Use screws (enclosed inside of box with
exhaust flange) to install exhaust flange
on air condioner as shown in Figure 18.
AMBIENT AIR ADAPTER
(Oponal)
An ambient air adapter can be purchased separately. Air adapter fits over the
condenser to duct condenser air to the unit to improve cooling efficiency.
1. Remove air adapter from carton.
2. Place air adapter on the rear of air condioner.
3. Use screws (enclosed inside of box with air adapter) to install the adapter
on the air condioner as shown in Figure 19.
Figure 17 – Cool Air Outlet aachment
1. Remove the cool air outlet
hose(s) from the box.
2. Place the cool air outlet hose(s)
on the front top of the unit as
shown in Figure 17.
3. Use screws to install the cool air
outlet hose(s) to the front of the
unit (screws aached to the cool
air outlet hose).
Component Parts
Power Cord Holder
Rubber Stoppers
Discharge Ducts /
Supply Air Duct
EXHAUST FLANGE
(Oponal)
