IN.XE ERROR CODES
DESCRIPTION
Hr
An internal hardware error has been detected in the in.xe.
Contact dealer or service supplier.
AOH
Temperature inside the hot tub skirt is too high, causing the internal temperature in
the in.xe to increase above normal limits. Open skirt and wait until error clears.
Prr
A problem is detected with the temperature probe.
Call your dealer or service supplier.
HL
The system has shut the heater down because the temperature at the heater has
reached 119°F (48°C).
Do not enter the water! Remove the hot tub cover and allow the water to cool down, then
shut power off and power your hot tub up again to reset the system.
FLO
The system does not detect any water flow while the primary pump is running.
Check and open water valves. Check for water level.
Clean filter. If the problem persists, call your dealer or service supplier.
OH
The water temperature in the hot tub has reached 108°F (42°C).
Do not enter the water! Remove the hot tub cover and allow the water to cool down to a
lower temperature.
Call your dealer or service supplier if problem persists.
TROUBLESHOOTING SECTION
Should an error occur, the display will show one of the following error messages toggled with the clock and the water
temperature.
SMART WINTER
MODE
Our Smart Winter Mode pro-
tects your system from the cold
by turning pumps on several
times a day to prevent water
from freezing in pipes.
The “SWM” indicator lights
up when freezing is detected
and flashes when the purge
is active.
SETTING TEMPERA-
TURE UNIT
Water temperature can be
displayed in either Fahrenheit
(°F) or Celsius (°C). The display
will show F or C.
Use the Up or Down key to
change the setting. Use
the Light key to save all the
parameters.
USER INTERFACE - EASY 4
COOLDOWN
After heating the hot tub wa-
ter to the desired Set Point,
the heater is turned off, but
its associated pump (Pump 1
low-speed or CP) remains on
for a predetermined period
of time to ensure adequate
cooling of the heating
element, prolonging its
useful life.
WATER TEMPERA-
TURE REGULATION
Every 15 to 90 minutes the
pump will run to ensure
accurate water temperature
readings as well as avoid heater
activation in dry conditions.
After verifying pump activation
and taking a water temperature
reading if required, the system
automatically turns the heater
on to reach and maintain water
temperature at Set Point.
Indicator flashes when
taking water temperature
reading.
39
Содержание Amazon W-Flow
