Welch Allyn PneumoCheck 61000 Скачать руководство пользователя страница 64

Страница: 64 / 90

Service Manual 610132 Rev. E

Pneumocheck Handle Printer/Charger 63

NOTE:

Torque the bolt (item 19, 21, and 22) to

3 - 4 in. lbs.

Removing the BASE HOUSING ASSEMBLY
(item 17)

Remove the TOP PANEL ASSEMBLY
(item 1) as instructed in Part A.

Remove the MAIN P.C. BOARD
ASSEMBLY (item 14) as instructed in
Part D, Steps 2 - 4.

Remove the TRANSFORMER
ASSEMBLY (item 8) as instructed in
Part F, Steps 3 - 7.

Remove the RFI FILTER (item 7) as
instructed in Part G, Steps 4 -5.

Remove the BASE HOUSING
ASSEMBLY.

Reassembly is the reverse of disassembly.

Removing the ROTARY SWITCH ASSEMBLY
(item 38).

Remove the TOP PANEL ASSEMBLY
(item 1) as instructed in Part A.

Peel off the PRINTER/CHARGER ESD
LABEL (item 37). Be sure to remove all
the adhesive from the TOP PANEL
ASSEMBLY (item 1).

Remove ROTARY SWITCH
ASSEMBLY.

Reassembly is the reverse of disassembly.

NOTE: Always use a new ESD LABEL (item 37).

Section 5 - Disassembly and Repair

Содержание PneumoCheck 61000



























































































Результаты поиска

Содержание PneumoCheck 61000

Отзывы:

Похожие инструкции для PneumoCheck 61000

Бренды по названию

Популярные бренды

Welch Allyn PneumoCheck 61000, Руководство по обслуживанию

Результаты поиска

Содержание PneumoCheck 61000

Отзывы:

Похожие инструкции для PneumoCheck 61000

Бренды по названию

Популярные бренды