Welch Allyn PneumoCheck 61000 Скачать руководство пользователя страница 59

Страница: 59 / 90

58 Pneumocheck Handle and Printer/Charger

Service Manual 610132 Rev. E

The RED wire of the connector to the rotary
board (part of the TOP PANEL ASSEMBLY)
should be to the RIGHT.

Torque (items 18 and 19) to 3 - 4 in. lbs.
Torque (item 2) to 2.7 - 3 - 4 in. lbs.

Removing the CONTROL P. C. BOARD
ASSEMBLY (item 10)

Remove the TOP PANEL ASSEMBLY
(item 1) as instructed in Part A.

Remove the three screws (item 26) that
hold the CONTROL P .C. BOARD
ASSEMBLY.

Remove the CONTROL P.C. BOARD
ASSEMBLY.

Reassembly is the reverse of disassembly.

NOTE:

Torque (item 26) to 1.0 - 1.5 in. lbs.

Removing the SPRING CONTACTS (item 13)

Remove the TOP PANEL ASSEMBLY
(item 1) as instructed in Part A.

Remove the screws (items 12) securing
the SPRING CONTACTS to the MAIN
P.C. BOARD ASSEMBLY (item 14).

Remove the SPRING CONTACTS.

Reassembly is the reverse of disassembly.

Torque item 12 to 1.5 - 2.0 in.lbs.

Section 5 - Disassembly and Repair

Содержание PneumoCheck 61000



























































































Результаты поиска

Содержание PneumoCheck 61000

Отзывы:

Похожие инструкции для PneumoCheck 61000

Бренды по названию

Популярные бренды

Welch Allyn PneumoCheck 61000, Руководство по обслуживанию

Результаты поиска

Содержание PneumoCheck 61000

Отзывы:

Похожие инструкции для PneumoCheck 61000

Бренды по названию

Популярные бренды