Weishaupt WHI sol/aqua 20 1 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 36

Weishaupt WHI sol/aqua 20 1 Скачать руководство пользователя страница 20

Installation and operation instructions

Separation station WHI sol/heat 20 #1 / 40 #1; Separation station WHI sol/aqua 20 #1 / 40 #1

6 Commissioning

83514202

▪

1/2014-06

▪

Ext. PAW

20-36

6.3

Flushing and filling the solar circuit (upper connections)

The fill and drain valves required for flushing and filling have been integrated into the

separation station. Make sure that dirt particles that may be present in the system are

not flushed into the heat exchanger and into the expansion tank. To do so, it may be

necessary to disconnect the expansion tank during flushing and filling and to use only

flushing and filling stations that are equipped with suitable microfilters.
The solar circuit is flushed in the normal direction of flow. This is why you should make

sure that the solar circuit pump is not on.

Ball valve with integrated check valve

(Normal direction of flow in the picture: downstream)

0°

45°

90°

Check valve in operation,

through-flow in flow direction

only.

Check valve not in operation,

through-flow in both

directions.

Ball valve closed,

no through-flow.

To actuate the ball valve, a handle is included in the delivery.

«
...
18
19
20
21
22
...
»

Содержание WHI sol/aqua 20 1





































Отзывы:

Нет отзывов