Weishaupt WHI sol/aqua 20 1 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 36

Weishaupt WHI sol/aqua 20 1 Скачать руководство пользователя страница 10

Installation and operation instructions

Separation station WHI sol/heat 20 #1 / 40 #1; Separation station WHI sol/aqua 20 #1 / 40 #1

3 Product description

83514202

▪

1/2014-06

▪

Ext. PAW

10-36

3.1

Function

To protect the solar circuit of a thermal solar system from frost, it is filled with a

propylene glycol/water mixture. The heat produced by solar energy is required in the

heating circuit or else in the potable water mains.
In small installations, this function is performed in most cases by a plain tube heat

exchanger integrated into the storage tank. When the collector fields become larger,

the transfer capacity of these heat exchangers is no longer sufficient.
In large systems, the function of separation stations is to transmit the heat energy

collected in the collector to the heating water circuit or to the potable water mains.
The centrepiece of these modules is a plate heat exchanger, whose cross-flow operating

mode allows excellent heat transfer.
The operating conditions in the heat exchanger vary, due to variations in radiation, buffer

temperatures and different system requirements.

For optimum operation of the overall system, the flow rates in the heat exchanger must

be adapted to the relevant control target and current situation.
To this end, high-efficiency pumps, which have an extremely wide control range, are

used in the WHI sol modules. This allows the controller to adapt the pumps optimally to

the momentarily required flow rate within a very broad application range.
Moreover, the pumps used save far more than 50% of the electrical drive energy

compared with customary asynchronous pumps.
The controller is delivered preset, assembled and wired, thus ensuring easy adjustment

to the real system.
The use of flow rate sensors in the WHI sol modules moreover offers an integrated heat

quantity measurement.
The WHI sol modules are equipped with safety, locking and flushing valves and fittings,

allowing the solar system to be commissioned safely and quickly.
The WHI sol/heat modules are intended for operation in heating installations.

In contrast, the WHI sol/aqua modules are used for separating the solar circuit from the

potable water mains.

«
...
8
9
10
11
12
...
»

Содержание WHI sol/aqua 20 1





































Отзывы:

Нет отзывов