Weishaupt WHI sol/aqua 20 1 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 36

Weishaupt WHI sol/aqua 20 1 Скачать руководство пользователя страница 19

Installation and operation instructions

Separation station WHI sol/heat 20 #1 / 40 #1; Separation station WHI sol/aqua 20 #1 / 40 #1

6 Commissioning

83514202

▪

1/2014-06

▪

Ext. PAW

19-36

6.1

Preparation for flushing and filling

NOTICE

Note regarding the expansion tank
To prevent any dirt particles contained in the solar system from

being flushed into the expansion tank, some manufacturers

recommend disconnecting the expansion tank from the solar

circuit during flushing and filling. Please observe the

manufacturer's instructions.

6.2

Flushing and filling the storage tank circuit / potable water circuit
(lower connections)

The storage tank and potable water circuits are filled by means of the valves and fittings

of the heating system. To prevent dirt particles from entering the heat exchanger, shut

the ball valves or piston valves of the station and flush dirt particles/scale residues from

the storage tank before commissioning. Make sure to only use admissible medium (see

chapter 3.2).

1.

Open the ball valves [C|D] of the WHI sol/heat module or the piston valves of

the WHI sol/aqua module [C|D] and disable the check valves

(45°, see next page).

2.

Vent the storage tank circuit or potable water circuit by actuating the fill and

drain valve [A].

3.

Make sure that no water enters the electrical components.

4.

Fill the storage tank circuit or potable water circuit.

5.

After filling the storage tank circuit or potable water circuit is complete, set the

required operating pressure.

6.

Vent the station during commissioning on the fill and drain valve [A], to remove

any air that may still be present in the heat exchanger.

It may be necessary to vent the pump (unscrew screw on pump head).

Separation station WHI sol/heat 20

Separation station WHI sol/aqua 20

«
...
17
18
19
20
21
...
»

Содержание WHI sol/aqua 20 1





































Отзывы:

Нет отзывов