©
2019 WEINZIERL ENGINEERING GmbH
Page 6/8
Wait to send after bus voltage recovery (Enabled / Disabled)
If enabled, the
parameter ‘Waiting time’ (10 s – 120 s) appears.
The set value determines the waiting time, until diagnostic tele-
grams will be sent after bus voltage recovery. The telegrams of
the following group objects will be restrained:
- Diagnostics
– Voltage [V] – Value
- Diagnostics
– Current [A] – Value
- Diagnostics
– Current max. – Value
- Diagnostics
– Temperature [°C] – Value
- Diagnostics
– Temperature max. – Value
- Diagnostics
– Busload [%] – Value
Device reset via menu (Enabled / Disabled)
By disabling this option, the function for resetting the device by
its local menu is deactivated.
Diagnostics
This parameter sets basic diagnostic functions.
Send diagnostic values (Disabled)
No group objects for diagnostic values are available.
Send diagnostic values (Cyclic)
The group object for diagnostic values are available.
The associated group telegrams will be sent in dependence of
the set cycle time.
Send diagnostic values (On change)
The group objects for diagnostic values are available.
The group telegrams will only be sent if the value changes.
Send diagnostic values (Cyclic and on change)
The group objects for diagnostic values are available.
The group telegrams will be sent in dependence of the set cycle
time as well as when the value changes.
Send diagnostic values (On request only)
The group objects for diagnostic values are available.
The telegrams will only be sent if triggered by a telegram to
group object
- Diagnostics
– Request values – Trigger.
If the diagnostic values are activated, the group objects
- Diagnostics
– Request values – Trigger
- Diagnostics
– Reset max. values – Trigger
are always available.
If a group telegram is sent to
‘request values trigger’ all diagnos-
tics values will be sent to the bus.
If
‘Reset max. values’ is triggered, the values of diagnostic ob-
jects “Current max.” and “Temperature max.” are reset to the
actual values and sent to the bus for confirmation.
B.
Alarm
This parameter sets basic alarm functions.
Send alarm (Disabled)
No group object for alarm states are available.
Send alarm (On alarm / On alarm and alarm end)
If activated the alarm state group objects as well as the threshold
options appear.
‘Threshold current min. [mA]’ option declares the minimum
amount of current. If the actual current falls below the chosen
threshold, the message associated to group object
‘Alarm – Current min. – State’ will be sent.
‘Threshold current max. [mA]’ option declares the maximum
amount of current. If the actual current rises above the chosen
threshold, the message associated to group object
‘Alarm – Current max. – State’ will be sent.
‘Threshold temperature [°C]’ determines the maximum of al-
lowed temperature. If the actual temperature within the housing
rises above the chosen threshold, the message associated to
group objec
t ‘Alarm - Temperature – State’ will be sent.
If the actual values
return into the ‘no alarm zone’ only a mes-
sage will be sent if option ‘On alarm and alarm end’ is chosen.
The measured current is the combined value of bus
and auxiliary output.
Group Object
Type KNX Size
Direction
11: Diagnostics
– Request values - Trigger
1.017
1 Bit
From KNX
12: Diagnostics
– Reset max. values -
Trigger
1.017
1 Bit
From KNX
13: Diagnostics
– Voltage [V] - Value
14.027
4 Byte
To KNX
14: Diagnostics
– Current [A] - Value
14.019
4 Byte
To KNX
15: Diagnostics
– Current max. [A] - Value
14.019
4 Byte
To KNX
16: Diagnostics
– Temperature [°C] - Value
9.001
2 Byte
To KNX
17: Diagnostics
– Temperature max. [°C] -
Value
9.001
2 Byte
To KNX
18: Diagnostics
– Busload [%] - Value
5.001
8 Bit
To KNX
Group Object
Type KNX
Size
Direction
20: Alarm
– Current min. - State
1.005
1 Bit
To KNX
21: Alarm
– Current max. - State
1.005
1 Bit
To KNX
22: Alarm
– Temperature – State
1.005
1 Bit
To KNX
