Weil-McLain New Series 3 Скачать руководство пользователя

Страница: 22 / 40

Series 3

WATER

BOILER

— Boiler Manual

Connect oil piping

Figure 16

Recommended oil piping connection to burner (follow applicable code requirements and
burner manual for component locations)

General oil piping requirements:

•

Location and installation of oil tanks, oil piping and
burners must follow:

• NFPA 31, Standard for the Installation of Oil-Burning

Equipment.

• In Canada, CSA B139, Installation of Oil-Burning

Equipment.

• Local codes and regulations.
• Information provided with burner and

fuel pump.

•

If any part of fuel oil tank is above level of burner,
an anti-siphon device must be used to prevent ﬂ ow
of oil in case of oil line break.

•

Support oil lines as required by codes.

•

Make tank connections with swing joints or copper
tubing to prevent breaking in case the tank settles.

Make swing joints so they will tighten as tank settles.
Non-hardening pipe joint compounds should be
used on all threads.

Do not use Teﬂ on tape as an oil pipe seal-

ant. It can cause valves to fail, creating
hazards. Do not use compression ﬁ ttings.

•

Underground pipe must be run in a casing to pre-
vent oil leaking into ground or under ﬂ oor. Check
local codes for information.

Oil piping connection at burner:

• See Figure 16 for recommended connection at

burner, allowing burner mounting door to swing
open completely for servicing.

Part number 550-142-182/1014

Содержание New Series 3









































Результаты поиска

Содержание New Series 3

Отзывы:

Похожие инструкции для New Series 3

Бренды по названию

Популярные бренды

Weil-McLain New Series 3, Инструкция по установке, запуску и эксплуатации

Результаты поиска

Содержание New Series 3

Отзывы:

Похожие инструкции для New Series 3

Бренды по названию

Популярные бренды