Weil-McLain Evergreen EVG 110 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 144

background image

Installing propane oriﬁ ce —
EVG 110 only

If the boiler is already installed

— You must turn

off electrical supply to the boiler and close the external
manual gas shut-off valve to isolate the boiler during
conversion. Allow the boiler to cool if it has been
operating.

Following conversion of an installed boiler, follow
all instructions in this manual to start up the boiler
and verify operation of the boiler and all system
components.

1. Locate the propane oriﬁ ce from the propane conversion kit bag.
2. Verify that the stamping on the oriﬁ ce is correct for the model

size (see Figure 13 ).

3.  If the jacket door is not already removed, remove it.
4.  Locate the gas valve and venturi (see Figure 14 ).
5.  Release the gas line from the silencer bracket clip (item 5, page

18) and rotate it out of the way.

6. Use a T25-mm torx bit to remove the two (2) bolts (item 3)

that secure the gas valve to the venturi.

Figure 13

Propane gas oriﬁ ce identiﬁ cation

EVG

110 (may be stamped

3.7

only)

Figure 14

EVG 110 Gas valve and venturi

Part number 550-100-191/0917

17

®

g

as-fired water boiler —

70/110/155

Boiler Manual

Converting boiler to propane — EVG 110

1

Gas valve

2

Venturi

3

Gas valve screws to venturi

Support the gas valve after disconnecting
it. DO NOT allow it to hang from the gas
valve ﬂ ex line.

When re-attaching the gas

valve, ensure the gas valve propane oriﬁ ce
is properly seated in rubber boot (item 6,
Figure 15, page 18 ) and is in place and in good
condition. Inspect the gas valve ﬂ ex line to
ensure it is undamaged and in good condition.

Prepa re boiler for propane —
EVG 110 only (if required)

Propane operation

ALL Evergreen

®

boilers must be converted

for propane operation

.

Converting an existing natural gas-ﬁ red
boiler for propane

— For a boiler already

installed, you must turn off gas supply, turn
off power and allow boiler to cool before
proceeding. You must also completely test the
boiler after conversion to verify performance
and start up the boiler following instructions
beginning on page 91 of this manual.

Verify 110 propane gas orifice size

—

See Figure 13 . Verify when installing that the
oriﬁ ce size marking is correct. Oriﬁ ces will be
stamped as in illustration or “3.7” for model
110.

Failure to comply could result in severe personal
injury, death or substantial property damage.

«
...
15
16
17
18
19
...
»

Содержание Evergreen EVG 110

















































































































































Отзывы:

Нет отзывов

Похожие инструкции для Evergreen EVG 110

Бренд: Radiant Страницы: 16

LOGIC SYSTEM S15IE

Бренд: Ideal Heating Страницы: 80

Бренд: VHH Страницы: 6

Бренд: Radiant Страницы: 60

Бренд: Lamborghini Caloreclima Страницы: 40

Бренд: U.S. Boiler Company Страницы: 176

Бренд: Ferroli Страницы: 28

Бренд: IDEAL Страницы: 52

KSM-Multistoker 575-50

Бренд: KSM-Stoker Страницы: 68

Бренд: Raypak Страницы: 5

Бренд: Ferroli Страницы: 24

Бренд: Aerco Страницы: 118

Benchmark 2.0 LN

Бренд: Aerco Страницы: 168

Benchmark BMK 1000

Бренд: Aerco Страницы: 178

Бренд: croydon Страницы: 2

Бренд: croydon Страницы: 2

Hercules Condensing 26 2 E

Бренд: Immergas Страницы: 72

Бренд: Thermo-Dynamics Boiler Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды