background image

Stripping and crimping machine 

 

Crimpfix 2.5 M  

08-09-19-DK-Operating Manual_gb.doc / 2008-09-19

  

3. 

Safety and the environment 

3.1 General 

Only the intended using ensure the operational safety of the machine. 
 
This manual contains important safety directions. All people working at the machine have to observe them. 
 
 

3.2 Safety 

instructions 

Depending on the model, the Crimpfix 2.5 M is configured with a power supply for AC voltage of either115 V or 
240 V. 
 

Caution: 

Only plug the Crimpfix 2.5 M into an outlet with an earth (ground) connection. 
The Crimpfix 2.5 M should only be operated in a dry environment with no exposure to moisture (splashed water, 
fog, etc.). 
 
 

3.3 Safety 

precautions 

Read the following instructions carefully before starting up the Crimpfix 2.5 M. Observe the warnings and notes 
on the Crimpfix 2.5 M at all times. 

  Do not insert any unsuitable objects into the openings. 

  Do not spill any fluids onto the Crimpfix 2.5 M. 

  The mains voltage must correspond to the system voltage given on the Crimpfix 2.5 M type plate. 

 
CAUTION! 

  Only connect the machine to a properly earthed and correctly-fused plug socket outlet. 

  Do not use a plug socket outlet already being used by devices that are turned on and off in regular intervals, 

such as photocopiers or fans. 

  Do not connect the Crimpfix 2.5 M to either a switched or a time – controlled plug socket outlet. 

 

  Never use damaged or scuffed power cables. 

  If you connect the Crimpfix 2.5 M to the power supply via an extension cable, ensure that the total nominal 

current of all the devices connected to the extension cable does not exceed the ampere rating for that 
extension cable. In addition, you should ensure that the total nominal current of all the devices plugged into 
the wall – mounted socket outlet does not exceed the ampere rating for that wall – mounted socket outlet. 

 
CAUTION! 

Do not carry out repairs to the device yourself. 
 

Unplug the Crimpfix 2.5 M and contact a qualified service engineer if anything of the following occurs: 

  The power cord or plug are scuffed or damaged. 

  Fluid has penetrated the Crimpfix 2.5 M. 

  The Crimpfix 2.5 M is fallen down or the enclosure is damaged. 

  The Crimpfix 2.5 M does not operate normally or the standard of performance varies noticeably. 

 
When contacting the manufacturer for any information please have the machine type and fabrication number 
available!(see type plate on the machine) 
 

3.4 Setup 

Select a suitable location for the setup, considering the following factors: 
  

  Place the Crimpfix 2.5 M on a flat, stable surface larger than the base area of the machine. 

  Ensure that there is sufficient space to allow the operator to push in cables without any restriction 

 

Содержание Crimpfix 2.5 M





















Отзывы: