background image

Adjusting the Press Plate

To adjust the distance
between the Small Seat
(29) and the Press Plate
(6), remove the Adjustment
Pin (26) from the Base (2).
Slide the Adjustment Frame
(3) into or out of the Base
until the Press Plate is in
the correct position. Insert
the Adjustment Pin into the
indicated hole in the Base and a hole in the Adjustment
Frame. 

This section explains how the body toning system can be adjusted. Inspect and tighten all parts each time you use the
body toning system. Replace any worn parts immediately. The body toning system can be cleaned with a damp cloth
and a mild, non-abrasive detergent. Do not use solvents.

Adjusting the Resistance

To change the amount of
resistance, remove the four
Spring Clips (5) from the
bench. Attach the 25-lb.
Bands (25) to the bars on
the Base (2) and the Pivot
Frame (7). Secure the
Bands with the four Spring
Clips.

The 10-lb. Bands (28) can be attached in the same man-
ner. Attach both sets of Bands for maximum resistance.

WARNING:

Always place an equal

amount of resistance on each side of the body ton-
ing system.

WARNING:

To reduce the risk of serious injury, read the following important precautions before

using the body toning system.

1. Read all instructions in this manual before using

the body toning system. Use the body toning
system only as described in this manual. 

2. It is the responsibility of the owner to ensure

that all users of the body toning system are ade-
quately informed of all precautions.

3. The body toning system is intended for home

use only. Do not use the body toning system in a
commercial, rental or institutional setting.

4. Use the body toning system only on a level sur-

face. Cover the floor beneath the body toning
system for protection of the floor.

5. Inspect and tighten all parts each time you use

the body toning system. Replace any worn parts
immediately. 

6.    Keep children under 12 and pets away from the

body toning system at all times.

7. 

If you feel pain or dizziness at any time while
exercising, stop immediately and begin cooling
down.

8. Keep hands and feet away from moving parts.

9. Always make sure there is an equal amount of

resistance on each side of the body toning sys-
tem.

10. The body toning system is designed to support a

maximum of 250 pounds.

11. Always wear athletic shoes for foot protection

while exercising.

WARNING:

Before beginning this or any exercise program, consult your physician. This is

especially important for persons over the age of 35 or persons with pre-existing health problems. Read all
instructions before using. ICON assumes no responsibility for personal injury or property damage sustained
by or through the use of this product. 

5

26

2

3

6

29

2-Bar

7-Bar

25

Adjusting the Body Toning System

Important Precautions

Содержание WEBE09910









Отзывы: