Thank you for selecting the versatile WEIDER
®
TWO
TONE body toning system. The TWO TONE body toning
system is designed to help you develop every major mus-
cle group of the body. Whether your goal is a shapely fig-
ure, dramatic increase in muscle size and strength, or a
healthier cardiovascular system, the TWO TONE body ton-
ing system will help you achieve the specific results you
want.
For your benefit, read this manual carefully before
using the WEIDER
®
TWO TONE body toning system.
If
you have additional questions, please call our Customer
Service Department toll-free at 1-800-999-3756, Monday
through Friday, 6 a.m. until 6 p.m. Mountain Time (exclud-
ing holidays). To help us assist you, please mention the
product model number (WEBE09910) and the serial num-
ber found on a decal attached to the body toning system
(see the front cover of this manual).
1.Press two 2” Round
Outer Caps (23) onto
each of the two Front
Stabilizers (9) and
the two Rear
Stabilizers (not
shown).
Attach a Front Stabilizer (9) to the Ab Leg (12) with two
5/16” x 2 1/2” Carriage Bolts (31) and two 5/16” Nylon
Locknuts (34).
Attach a Rear Stabilizer (not shown) to the other end of
the Ab Leg (12) in the same manner.
Note: The Front
Stabilizers (9) are shorter than the Rear Stabilizers.
2.Insert a 5/16” x 3”
Carriage Bolt (32)
into the center hole in
the Large Support
Plate (14). Attach the
Large Support Plate
to the Large Seat
(13) with two 1/4” x
3/4” Screws (40).
Press a 1” x 2” Inner
Cap (30) into the
lower end of the Seat
Frame (15).
Insert a 5/16” x 3” Carriage Bolt (32) into the indicated
hole in the Seat Frame (15). Insert the 5/16” x 3”
Carriage Bolt in the Large Support Plate (14) through
the rear hole in the Seat Frame.
Attach the Large Seat (13) to the Seat Frame (15) with
the 1/4” x 1/2” Screw (39).
Secure the two 5/16” x 3” Carriage Bolts (32) to the Ab
Leg (12) with two 5/16” Washers (35) and two 5/16”
Nylon Jamnuts (46).
1
3.Hold the Metal
Bushing (27) inside
the Seat Frame (15).
Slide a 5/16” x 1 3/4”
Bolt (33) into the
upper hole in the Ab
Frame (11), the Seat
Frame, and the Metal
Bushing.
Slide another 5/16” x
1 3/4” Bolt (33) into
the lower hole in the
Ab Frame (11) and the Seat Frame (15).
Secure the two 5/16” x 1 3/4” Bolts (33) with two 5/16”
Washers (35) and two 5/16” Nylon Locknuts (34).
Press a 1” x 2” Inner Cap (30) into the upper end of the
Seat Frame (15).
4.Remove the 1/4” x
3/4” Type F Screws
(47) from the Ab
Frame (11). Attach
the Ab Handlebars
(10) to the Ab Frame
with the two 1/4” x
3/4” Type F Screws.
Press a 1 1/8” Round
Inner Cap (16) into
each Ab Handlebar
(10).
Wet the Ab
Handlebars (10) and the Ab Frame (11) with soapy
water. Slide a Short Cover Sleeve (48) onto each side
of the Ab Frame. Slide a Long Cover Sleeve (17) onto
each Ab Handlebar.
2
3
11
33
23
23
34
12
34
31
13
15
14
32
32
40
12
39
40
30
46
35
9
35
34
30
15
27
4
10
10
11
16
47
17
48
47
16
Before You Begin
Assembly—Ab Tilt & Tone
