manualshive.com logo in svg

WEG MMW03-M22CH, Руководство пользователя

Поделиться
Скачать
WEG MMW03-M22CH Скачать руководство пользователя страница 14

www.weg.net

14 | Energy Analyzer - MMW03-M22CH

3 MENUS

3.1 INSTANTANEOUS MEASUREMENT MENUS

Voltage (L-N and L-L), current, neutral current, cosØ, power factor, active power, reactive power, apparent power, 
THDV and THDI values are shown in instantaneous menu.

Menu are given the name of which is shown in Menu bar.

The values shown on the display is expressed in what phase or phases at the lower left corner of the display 
numbers.

Phase Numbers are not displayed at Menus which display avarege, total and other properties of network. In this 
case phases are displayed in 2. Level.

Next to each index value unit of respective rows are indicated. It also states that inductive or capacitive phases 
are indicated next to the relevant indicators.

Table 1-3 for parameters displayed in the menus.

POWER Q

Figura 3.1: Instantaneous Measurement Menus (Reactive Power)

CAUTION!

When the product is mounted on a panel which consumes power, active power (P) must be positive. If active power is 
negative, operator should cross connect k-l leads of the current transformer.
When the product is mounted on a panel which generates power, active power (P) must be negative. If active power is 
positive, operator should cross connect k-l leads of the current transformer.

3.2 MAXIMUM, MINIMUM VE DEMAND MENUS

Minimum and maximum values are calculated and stored in the non-volatile memory for below parameters:

 

„

Voltage (phase-neutral, phase-phase);

 

„

Neutral current;

 

„

Frequency;

 

„

CosØ;

 

„

Power factor;

 

„

THDV;

 

„

THDI.

Содержание MMW03-M22CH













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды