Weco WF-103, Инструкция по эксплуатации, Страница: 3 / 32

WF-103
Cod.006.0001.1040
10/07/2017 v2.12
ENGLISH
0
1 INTRODUCTION ................................................................. 4
2 FRONT PANEL ................................................................... 4
3 REAR PANEL ..................................................................... 5
4 INSTALLATION .................................................................. 5
4.1 PREPARING FOR MIG/MAG WELDING ............................. 5
4.2 PREPARING FOR MMA WELDING ..................................... 5
4.3 WIRE SPOOL POSITIONING .............................................. 8
4.4 POSITIONING THE WIRE IN THE WIRE FEEDER .............. 8
5 USER INTERFACE ........................................................... 10
6 UNIT POWER-UP.............................................................. 12
6.1 POWER SOURCE MANAGEMENT BY REMOTE CONTROL
......................................................................................... 12
7 RESET (LOAD FACTORY SETTINGS) ............................. 12
7.1 TOTAL RESET .................................................................. 12
8 SET-UP (INITIAL SET-UP OF THE WELDING POWER
SOURCE).......................................................................... 13
COOLER ACTIVATION ................................................................ 13
REMOTE CONTROLLER SELECTION ......................................... 13
ADJUSTMENTS BLOCK SELECTION .......................................... 13
PUSH PULL ................................................................................. 13
SELECTION OF BURN TYPE....................................................... 13
8.1 LOCKING PROCEDURE ................................................... 14
Enabling ....................................................................................... 14
Disabling ...................................................................................... 14
8.2 TORCH LOADING ............................................................. 15
9 ALARMS MANAGEMENT ................................................. 15
AL. HEA. ...................................................................................... 15
AL. COO. ..................................................................................... 15
Err. C0 ......................................................................................... 15
Err. C1 ......................................................................................... 15
Err. C2 ......................................................................................... 15
Err. C4 ......................................................................................... 15
Err. C11 ....................................................................................... 15
Err. C12 ....................................................................................... 15
Err. C69 ....................................................................................... 15
AL. Cur......................................................................................... 16
AL. Mot. ....................................................................................... 16
10 WELDING PARAMETERS ................................................ 17
10.1 PARAMETERS ACTIVATION ............................................ 18
Working voltage ............................................................................ 18
Welding inductance ...................................................................... 18
WIRE FEED RATE ....................................................................... 18
WELDING CURRENT................................................................... 18
THICKNESS................................................................................. 18
PROGRAMS ................................................................................ 18
Hot Start ....................................................................................... 18
Crater Filler .................................................................................. 18
3 Levels Slope .............................................................................. 18
Soft Start ...................................................................................... 18
Motor Slope .................................................................................. 18
Bourn Back .................................................................................. 18
Post gas time ............................................................................... 18
Pre gas time ................................................................................. 18
11 WELDING SETTINGS ....................................................... 19
11.1 MIG/MAG WELDING ......................................................... 19
11.1.1 SETTING MIG/MAG PARAMETERS (MAIN WELDING
PARAMETERS) ........................................................................... 19
11.1.2 MIG/MAG PARAMETERS SETTING (2ND LEVEL) ....................... 20
11.1.3 MIG/MAG PARAMETERS SETTING (GAS MENU) ....................... 20
11.2 ELECTRODE WELDING (MMA) ........................................ 20
11.3 ARC AIR (DESEAMING) .................................................... 20
12 JOBS MANAGEMENT ...................................................... 21
12.1 SAVING A JOB.................................................................. 21
12.2 LOADING A USER JOB OF FACTORY SET JOB .............. 21
12.3 DELETING A JOB ............................................................. 22
13 TORCH TRIGGER MODES ............................................... 22
13.1 2T MIG/MAG WELDING .................................................... 22
13.2 4T MIG/MAG WELDING .................................................... 22
13.3 3 LEVEL MIG/MAG WELDING ........................................... 22
14 TECHNICAL DATA ............................................................ 23
15 SPARE PARTS.................................................................. 24
15.1 WF-103 .............................................................................. 24
15.2 WIRE FEEDER MOTOR .................................................... 26
15.3 WIRE FEEDER ROLLS ...................................................... 27
16 ELECTRICAL DIAGRAM ................................................... 28
16.1 WF-103 .............................................................................. 28
16.2 POWER SOURCE → WF-103 CABLE ............................... 29
16.3 REMOTE CONTROLLER ................................................... 30
16.3.1 RC03: ELECTRICAL DIAGRAM.................................................... 30
16.3.2 RC04: ELECTRICAL DIAGRAM.................................................... 30
16.3.3 RC05: ELECTRICAL DIAGRAM.................................................... 31
16.3.4 RC06: ELECTRICAL DIAGRAM.................................................... 31