manualshive.com logo in svg

Weco HeSU 5K3-LV HV, Руководство пользователя

Поделиться
Скачать
Weco HeSU 5K3-LV HV Скачать руководство пользователя страница 66

WeCo 5K3-LV-HV

HeSU 5K3-LV HV

Page 66 of 69

V_1.1_21-Nov-2020_LV-HV

3.6.1 LED Visual Indication Lights

Power Button

Each single module has its own run button but the HV box will take over the communication by activating or switching off
the HV module circuit

3.6.1.1 Power Button

The Power Button is located to the right of the battery terminal connections on the side of the battery. The Power Button is a
multi-color button and will provide the user with the following indications depending on the state of the battery

A 2-second press on the Power Button will turn the battery module on.
A 5-second press on the Power Button will turn the battery off

Other functions of the Power Button are explained in the relevant sections of this manual.

Attention:

Read this entire manual thoroughly to understand the correct start up and shut down procedures for each

battery configuration.

Attention:

Illustrations shown are for reference only, please always refer to the physical battery module in front of

you and if the module has a different configuration to this manual, stop all activity immediately and contact WeCo
support on

[email protected]

.

3.6.2 Stand Alone Battery Front Panel Control * FORCED CHARGE*

3.6.2.1 Start Battery

Press the power button of the HV BOX for 3 or more seconds (depends by the system status)
The GREEN RUN light should come on. The HV BOX module has been activated normally and the batteries modules should come on
automatically, if not press the run button of each module and wait for the HV BOX string diagnosis, if the HV BOX will show the
warning led light ( RED) turn the string OFF and connect the PC software for debug.

3.6.2.2 Shut Down batteries and HV Box

Long press the power button for five seconds of the run button of the HV box.
The GREEN RUN light should go off. The HV BOX has been shut down normally.
By switching off the HV BIX all the battery modules should turn off automatically, if not then shut down manually by pressing the run
button for 5 seconds.

Содержание HeSU 5K3-LV HV






































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды