Weco HeSU 5K3-LV HV Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 69

Weco HeSU 5K3-LV HV Скачать руководство пользователя страница 5

WeCo 5K3-LV-HV

HeSU 5K3-LV HV

Page 5 of 69

V_1.1_21-Nov-2020_LV-HV

Statement:

The information and guidance contained in this manual is related to the WeCo 5K3 – LV – HV Stackable model of battery
This manual contains two sections:

Section 02 is for LOW VOLTAGE APPLICATION

Section 03 is for HIGH VOLTAGE APPLICATION

In case of product upgrades or other reasons, this document will be adjusted accordingly. Unless otherwise agreed, this
document is intended to be used only as a guide, and all statements, information and advice in the documentation shall
not constitute any express or implied action in contradiction to local regulations or standards.
For more information, please contact us.

The official information and the latest datasheet are available on

www.wecobatteries.com

.

It is essential that the battery unit is equipped with the latest firmware version available.

New batteries always ship with the latest version of firmware.

WeCo will release new firmware to improve the functionalities and battery capabilities from time to time.
The latest version of the firmware is always available free of charge and can be updated by your local installer.
You can also write an email to

[email protected]

to understand the upgrade procedure.

ATTENTION

This battery model is designed to be used indoors

The STANDARD IP20 degree of protection does not allow installation in outdoor environments even if sheltered
from the weather.
The INDOOR definition means literally the internal environment, the room must be closed to unauthorized persons,
ventilated and dry.

PREFACE

Thank you for choosing our product. We will provide you with a high-quality product as well as reliable after service.
To protect against harm to both personnel and the product, please read this manual carefully.
This manual provides detailed information on operation, maintenance and troubleshooting of the product as well as health and
safety advice.

Special Announcement:

The manufacturer holds the right of final explanation of any content in this manual.

«
...
3
4
5
6
7
...
»

Содержание HeSU 5K3-LV HV






































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды