background image

DRIVE X FLEET

   

PROFESSIONAL VEHICLE SIGNAL BOOSTER KIT

14

Drive X

Product Number

U471010

Model Number

460021

FCC ID: 

PWO460021

IC ID:

4726A-460021

Connectors

SMA-Female

Antenna Impedance

50 Ohms

Frequency

699-716 MHz, 729-756 MHz, 777-786 MHz, 824-894 MHz, 1850-1995 MHz, 1710-1755 MHz/2110-2155 MHz

Maximum Power

Power output for single cell 

phone (Uplink) dBm

700 MHz  

Band 12/17

24.84

700 MHz  

Band 13

24.35

800 MHz  

Band 5

23.4

1700 MHz

Band 4 

21.3

1900 MHz  

Band 2

24.43

Power output for single cell 

phone (Downlink) dBm

700 MHz  

Band 12/17

2.87

700 MHz  

Band 13

2.79

800 MHz  

Band 5

2.8

2100 MHz

Band 4  

2.0

1900 MHz  

Band 2

1.92

Noise Figure

5 dB nominal

Isolation

> 90 dB

Power Requirements

6 V 2 A

______

Specifications

Each Signal Booster is individually tested and factory set to ensure FCC compliance. The Signal Booster cannot be adjusted without 

factory reprogramming or disabling the hardware. The Signal Booster will amplify, but not alter incoming and outgoing signals in order 

to increase coverage of authorized frequency bands only. If the Signal Booster is not in use for five minutes, it will reduce gain until a 

signal is detected. If a detected signal is too high in a frequency band, or if the Signal Booster detects an oscillation, the Signal Booster 

will automatically turn the power off on that band. For a detected oscillation the Signal Booster will automatically resume normal 

operation after a minimum of 1 minute. After 5 (five) such automatic restarts, any problematic bands are permanently shut off until the 

Signal Booster has been manually restarted by momentarily removing power from the Signal Booster. Noise power, gain, and linearity 

are maintained by the Signal Booster’s microprocessor.

The term “IC” before the radio certification number only signifies that Industry Canada technical specifications were met. This device 

complies with Part 15 of FCC rules. This device contains licence-exempt transmitter(s)/receiver(s that comply with Innovation, Science 

and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may 

not cause interference, and (2)) This device must accept any interference, including interference that may cause undesired operation of 

the device. Changes or modifications not expressly approved by weBoost could void the authority to operate this equipment.

NEED HELP?

support.weboost.com

1-866-294-1660

Содержание DRIVE X FLEET





















Отзывы: