Weber Markoprint XB4JET Скачать руководство пользователя страница 67

Страница: 67 / 162

Installation and initial operation

72800153 Markoprint XB4JET / XB8JET

Seite 67 von 162

Installation must be performed by specialised staff:

Mount the control system with the pre-assembled spring clip at a 35 mm DIN-cap rail.

For an alternative mounting of the control system are two (XB4JET) or four
(XB8JET) bushings at the bottom side of the system.

Compare

the

mains

data

with

the

technical

data

the

controller.



Chapter

Technical data

, Page 20

Connect only when the data corresponds!

Fig. 24: Controller, connection

Connect the mains cable to the mains socket (Fig. 24/1) of the controller.

Insert the mains plug into an earthed wall socket.

If a rotary Encoder is installed, connect the rotary Encoder

cable to the

ENCODER

socket

(Fig. 24/2) and tighten.

Connect the light barrier cable to the

SENSOR

socket (Fig. 24/3) and tighten.

Connect the print head cable of the first head (upper head) to the

HEAD 1

socket (Fig.

24/4) and tighten.

Connect the print head cable of the second head to the

HEAD 2

socket (Fig. 24/5) and

tighten. Further print heads can be connect accordingly.

If only one print head is used, the other connection is not used.

Содержание Markoprint XB4JET



































































































































































Результаты поиска

Содержание Markoprint XB4JET

Отзывы:

Weber Markoprint XB4JET, Руководство по установке, эксплуатации и техническому обслуживанию, Страница: 67 / 162

Результаты поиска

Содержание Markoprint XB4JET

Отзывы: