Weber Markoprint XB4JET Скачать руководство пользователя страница 29

Страница: 29 / 162

Transport, packaging and storage

72800153 Markoprint XB4JET / XB8JET

Seite 29 von 162

Symbols on packaging

This way up

The arrowheads indicate the top of the package. They must
always face upward to avoid damage to the content.

Fragile

Identifies packages with fragile or sensitive contents.

Handle the package with care, do not drop or subject to
impacts.

Keep dry

Keep packages away from moisture and keep dry.

Protect from heat

Protect packages from heat and direct sunlight.

Transport inspection

Check the delivery for completeness and transport damages immediately upon receipt.
Proceed as follows in case of externally visible transport damage:



Decline delivery or accept with reservation only.



Record extent of damage in the transport documentation or on the delivery note

of the haulier.



Initiate complaint.

Complain about each defect as soon as it is detected. Claims for damages can
only be made within the applicable claim periods.

Содержание Markoprint XB4JET



































































































































































Результаты поиска

Содержание Markoprint XB4JET

Отзывы:

Бренды по названию

Популярные бренды

Weber Markoprint XB4JET, Руководство по установке, эксплуатации и техническому обслуживанию

Результаты поиска

Содержание Markoprint XB4JET

Отзывы:

Бренды по названию

Популярные бренды