background image

31

Cooking

The Weber Genesis Gas Barbecue should not be
moved when operating or hot.

You can adjust the FRONT, CENTER and BACK burners
as desired. The control settings High (H), Medium (M),
Low (L), or Off (O) are described in your Weber
cookbook. The cookbook uses these notations to
describe the settings of the FRONT, CENTER, and
BACK burners. For example, to sear steaks you would
use (HHH) (all burners at high). Then to complete
cooking you would use (MOM) (FRONT at medium,
CENTER off, and BACK at medium). See your Weber
cookbook for detailed cooking instructions.

If burners go out during cooking, open lid, turn off
all burners and wait 5 minutes before relighting.

Note - The temperatures inside your cooking box, for the
first few uses, may be hotter than those shown in your
cookbook. Adjusting the burner controls may be
necessary.

CAUTION:  Replace thermometer in lid when not in

use. Do not leave thermometer in food while cooking.

Preheating

Your Weber Genesis Gas Barbecue is an energy
efficient appliance. It operates at a low B.T.U. rate for
economy. To preheat, after lighting, close lid and turn 
all burners to high (HHH). Preheating to between 500°
and 550° F (260° and 290° C) will take 10 to 15 minutes
depending on conditions such as air temperature 
and wind.

Drippings and grease

The Flavorizer Bars are designed to "smoke" the right
amount of drippings for flavorful cooking. Excess
drippings and grease accumulate in the catch pan under
the bottom tray. Disposable foil liners are available that
fit the catch pan.

Periodic Cleaning

CAUTION:  Turn your Weber Gas Barbecue OFF

and wait for it to cool before cleaning.

CAUTION:  Do not clean your Flavorizer Bars or

cooking grates in a self-cleaning oven. Replacement
cooking grates and Flavorizer Bars are available
through your retailer or the Weber-Stephen Customer
Service Center.

Outside surfaces - 

Use a warm soapy water solution. 

CAUTION:  Do not use oven cleaner, abrasive

cleansers (kitchen cleansers) cleaners that contain
citrus products or abrasive cleaning pads on
barbecue or cart surfaces.

Bottom tray - 

Wash with warm soapy water.

Flavorizer Bars and Cooking Grates- 

Clean with a

suitable brass bristle brush. As needed, remove from grill
and wash with warm soapy water.

Catch pan - 

Disposable foil trays are available, or you can

line the catch pan with aluminum foil. To clean the catch
pan, wash with warm soapy water.

Thermometer - 

Wipe with warm soapy water, clean with

plastic scrub ball. Do not put in dishwasher or submerge
in water.

Inside cooking box - 

Brush with a suitable barbecue

brush (brass bristle). Brush any debris off of burners with
barbecue brush. 

DO NOT ENLARGE BURNER PORTS

(OPENINGS). 

Wash inside box with warm soapy water.

Inside Lid - 

While lid is warm, wipe inside with paper

towel to prevent flaking due to grease build-up.

Storage and/or Nonuse

When storing the Weber Gas Barbecue, make sure
that the inside shut off valve and/or locking outdoor
shut off valve is secured in the OFF postion. When
the Weber Gas Barbecue is stored indoors, the gas
supply 

MUST BE DISCONNECTED.

After a period of storage and/or nonuse the Weber
Gas Grill should be checked for gas leaks and any
obstructions in the burner tubes before using. (See
Sections General and Annual Maintenance.)

Check that the areas under the control panel and
the bottom tray are free from debris that might
obstruct the flow of combustion or ventilation air.

The Spider Stopper Guards should also be 
checked for any obstructions. (See Section 
"Annual Maintenance.")

Содержание Genesis 5000 LP











































Отзывы: