Weber Genesis 5000 LP Скачать руководство пользователя | Manualshive

Страница: 14 / 42

background image

14

Step 9

Install the three back panels

You will need: frame assembly, two plastic buttons and
the three back panels. (Number 2)

Place the bottom of one back panel on the back frame
connector, notches to the top. Set in place to the far left,
butting up against the caster frame. Repeat the
procedure with the the other two back panels. Figure 8.

Figure 8

With all three panels in place and flush with each other,
push in the plastic buttons. They should cover the
flanges of the panels up against the wheel and caster
frames. Figure 9.

Figure 9

Wheel
frame

Caster frame

Step 10

Install side burner locks

You will need: frame assembly, 2 side burner locks and a
7/16 inch wrench.

Loosen the right rear 1/4 x 20 bolt. Install the side
burner lock. The “U” shape cut out of the lock slips down
over the bolt. Tighten with a wrench. Figure 10.

Loosen the right front 1/4 x 20 bolt. The side burner lock
fits between the front panel and the frame.
The “U” shape cut out slips up over the bolt.
Tighten with a wrench.

Figure 10

«
...
12
13
14
15
16
...
»

Содержание Genesis 5000 LP











































Отзывы:

Нет отзывов

Похожие инструкции для Genesis 5000 LP

Бренд: Falcon Страницы: 8

Бренд: Falcon Страницы: 6

Бренд: Falcon Страницы: 7

Бренд: Falcon Страницы: 6

Бренд: Jata Страницы: 24

Бренд: Cuisinart Страницы: 72

Бренд: Livoo Страницы: 8

BeachFire BF10-106

Бренд: Magma Страницы: 8

Бренд: Atlas Copco Страницы: 60

Бренд: NEO Страницы: 20

Бренд: Milwaukee Страницы: 13

Carleton GBC1449W-C

Бренд: BackyardGrill Страницы: 14

Бренд: Lassco Wizer Страницы: 25

Бренд: T-Fal Страницы: 16

Бренд: Nexgrill Страницы: 28

Бренд: Cadac Страницы: 13

Бренд: Dynabrade Страницы: 8

Бренд: Orbegozo Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды