Weber Genesis 5000 LP Скачать руководство пользователя

Страница: 1 / 42

Serial Number

Please use this number in registering your warranty
and any correspondence with the factory.

62715 6/96

Owner's Manual

FOR YOUR SAFETY
Do not store or use gasoline or other
flammable vapors and liquids in the
vicinity of this or any other appliance.

NOTICE TO INSTALLER: These
instructions must be left with the owner
and the owner should keep them for
future use.

WARNING: Follow all leak check
procedures carefully in this manual prior
to barbecue operation. Do this even if
barbecue was dealer assembled.

WARNING: Do not try to light this
appliance without reading "Lighting"
instructions section of this manual.

THIS GAS APPLIANCE IS DESIGNED FOR
OUTDOOR USE ONLY.

FOR YOUR SAFETY
If you smell gas:
1. Shut off gas to the appliance.
2. Extinguish any open flame.
3. Open lid.
4. If odor continues, immediately call

your gas supplier.

GENESIS

5000 Series

Propane Fixed Piping System

GAS
BARBECUE

Содержание Genesis 5000 LP











































Результаты поиска

Содержание Genesis 5000 LP

Отзывы:

Похожие инструкции для Genesis 5000 LP

Бренды по названию

Популярные бренды

Weber Genesis 5000 LP, Руководство пользователя

Результаты поиска

Содержание Genesis 5000 LP

Отзывы:

Похожие инструкции для Genesis 5000 LP

Бренды по названию

Популярные бренды