Weber mt CR 8 страница 7 Скачать руководство пользователя | Manualshive

Страница: 7 / 28

background image

CR

8

7

Inspection

Compactors must be inspected in accordance with appropriate implementation conditions and

operating conditions, as needed; however an inspection to ensure operationally safe status must be

performed by an expert at least once a year. The results of the inspection must be recorded in writing

and must be stored at least until the next inspection.

Cleaning work

Prior to cleaning the compactor with a high-pressure cleaner, protect all accessible energized

switches, cable connections, etc. against water penetration by masking them off.

Cleaning tasks should only be executed in areas that are suitable and have been approved for

this purpose (oil separator amongst others).

Disposal

All operating fluids and auxiliary materials must be disposed of in an environmentally-compatible

manner in accordance with country-specific regulations.

Important information for operating and maintenance personnel is marked by pictograms.

Warning against irritants or materials hazardous to health

Warning against a hazardous place

Warning against a suspended load

Wear ear protection

General regulation

Environmental protection

Hard hat

Safety shoes

Protective gloves

«
...
5
6
7
8
9
...
»

Содержание CR 8





























Отзывы:

Нет отзывов

Похожие инструкции для CR 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды