Weathermatic SmartLine Скачать руководство пользователя | Manualshive

Страница: 1 / 22

background image



SmartLine Controller Owner’s Manual (vG5)



Controller Program Template



Controller Basic Watering Schedule Template



Controller Smart Watering Schedule Template

1.0 Getting Acquainted With
Your SmartLine® Controller

SmartLine® is the smart choice for water conservation and beautiful landscaping. The “get acquainted”
information in this section will make programming your unit easier and faster.

1.1 Getting Acquainted With Your Control Panel

The SmartLine® Controller LCD Display provides the following information when the controller is set to
RUN, SYSTEM OFF, or when there is no active watering operation underway (display with program in IDLE
mode):

SmartLine Owner’s Manual

1
2
3
...
»

Содержание SmartLine























Отзывы:

Нет отзывов

Похожие инструкции для SmartLine

Бренд: 2gig Technologies Страницы: 4

Бренд: 2gig Technologies Страницы: 2

Бренд: G1SLE Страницы: 2

ESSENSSE NEO COMFORT

Бренд: 2VV Страницы: 21

AirGENIO SUPERIOR

Бренд: 2VV Страницы: 27

Бренд: Febco Страницы: 12

Бренд: GameSir Страницы: 8

Бренд: Game ready Страницы: 21

Бренд: VAMP Страницы: 304

Бренд: Tactical Страницы: 8

Бренд: Unitech Страницы: 55

Бренд: S&C Страницы: 8

ZITON RADIO LOOP MODULE

Бренд: EMS Страницы: 26

Бренд: Danfoss Страницы: 30

SAE 07.2 Series

Бренд: AUMA Страницы: 116

CentralControl CC41

Бренд: Becker Страницы: 48

Бренд: GSK Страницы: 32

Бренд: Procom Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды