Wayne-Dalton 8100, Инструкция по установке и руководство пользователя

Страница: 3 / 24

weatherstrip in the header and flush with the inside edge of the jamb. Temporarily secure
the weatherstrip with equally spaced nails. Repeat for other side. This will keep the bottom
section from falling out of the opening during installation. Equally space nails approximately
12” to 18” apart.
FOR FULLY ADJUSTABLE TRACK: For the header, align the weatherstrip 1/8” to 1/4” inside
the header edge, and temporarily secure it to the header with equally spaced nails. Starting
at either side of the jamb, fit the weatherstrip up tight against the temporarily attached
weatherstrip in the header and 1/8” to 1/4” inside the jamb edge. Temporarily secure the
weatherstrip with equally spaced nails. Repeat for other side. This will keep the bottom sec-
tion from falling out of the opening during installation. Equally space nails approximately 12”
to 18” apart.
HEADROOM REQUIREMENT:
Headroom is defined as the space needed above the top of
the door for tracks, springs, etc. to allow the door to open properly. If the door is to be motor
operated, 2-1/2” (64 mm) of additional headroom is required.
NOTE: 6” low headroom conversion kit is available for 12” radius only. Contact your local
Wayne Dalton dealer.
BACKROOM REQUIREMENT:
Backroom is defined as the distance needed from the opening
back into the garage to allow the door to open fully.
*NOTE: For door heights from 10’1” to 14’0”, refer to your operator manufacture installation
instructions for appropriate depth into room.
BACKROOM REQUIREMENTS
Door Height Track Manual Lift Motor Operated
6’0” to 7’0” 12”, 15” Radius 102” (2591 mm) 125” (3175 mm)
7’1” to 8’0” 12”, 15” Radius 114” (2896 mm) 137” (3480 mm)
8’1” to 9’0” 12”, 15” Radius 126” (3200 mm) 168” (4267 mm)
9’1” to 10’0” 12”, 15” Radius 138” (3505 mm) 168” (4267 mm)
10’1” to 12’0” 12”, 15” Radius 162” (4115 mm) See *NOTE
12’1” to 14’0” 12”, 15” Radius 186” (4724 mm) See *NOTE
HEADROOM REQUIREMENTS
Track Type Space Needed
12” Radius 13-1/2” (343 mm)
15” Radius 14-1/2” (368 mm)
Weatherstrips
Level heade
r
Finished
Door width
Jamb
s
Backroo
m
Plumb
jambs
Finished
Door
Height
Nail
Headroom
Header board 2”x 6”
lumber preferred
Suitable mounting surface
2”x 6” lumber minimum
Weatherstrips
Jamb
Quick Install track
Other track systems
Jamb
1/8” to 1/4”
Min. Side
room
Clearance
is 3-1/2”
Min. Side
room
Clearance
is 3-1/2”
Package Contents
NOTE: Depending on the door model, some parts listed will not be supplied if not required.
Rear Back Hangs may not be included with your door.
Door sections (as required)
Torsion shaft / Torsion keyed shaft (as required)
Torsion keyed shafts (as required)
Vertical tracks RH/LH (as required)
Q.I. flag angles RH/LH (as required)
F.A. flag angles RH/LH (as required)
Riveted vertical track assemblies RH/LH (as required)
Horizontal tracks RH/LH (as required)
Angle mount vertical track assemblies RH/LH (as required)
(2) Horizontal track angles (as required)
Quick install jamb
brackets (as required)
Fully Adjustable jamb
brackets (as required)
Weatherstrips &
nails (If included)
JB-US Jamb
brackets
(as required)
Strut (U-shaped)
(if included)
Bottom corner brackets
RH/LH (as required)
(2) Lift handles &
Spacers
(1) Step plate
(as required)
(2) Step plates
(as required)
(1) Step plates
(as required)
Pushnuts
(as required)
Top fixture assemblies
(as required)
Top fixture assemblies
(as required)
Graduated
hinges (as required)
Extension brackets
(as required)
Track rollers
(as required)
(2) Roller
spacers
Pull down
rope (if included)
Bottom corner
brackets (as required)
Bottom corner
brackets (as required)
Track roller carriers
(as required)
Cable drums RH/LH
3