background image

 

STOP USE IMMEDIATELY IF A PROBLEM OCCURS. 

Failure to do so may 

result in personal injury or damage to the product. Return it to your 
authorized Wāvtech dealer

.

 HAVE AN EXPERT DO THE WIRING AND INSTALLATION. 

This unit requires 

special technical skill and experience for wiring and installation. To insure 
safety and proper fun

ction, always contact the authorized dealer where you 

purchased the product to have it done professionally.

  

INSTALL THE UNIT SECURELY WITH SPECIFIED PARTS. 

Be sure to use only 

the included parts and specified installation accessories (not included). Use of 
other than designated parts may damage this unit.  Install the unit securely so 
that it will not come loose during a collision or sudden jolt.

 

ROUTE WIRING AWAY FROM SHARP EDGES AND MOVING PARTS.

 Arrange 

cables and wiring away from sharp or pointed edges and avoid moving parts 
such as seat hinges or rails to prevent pinching or wear. Use loom protection 
where appropriate and always use a grommet for any wiring routed through 
metal. 

 NEVER RUN SYSTEM WIRING OUTSIDE OR UNDERNEATH THE VEHICLE.  

All wiring must 

be routed, secured and protected inside the vehicle. Failure to 

do so may result in fire, injury or property damage.

 

INSTALL THE UNIT IN A DRY AND VENTILATED LOCATION.

 Avoid 

mounting locations where the unit will likely be exposed to high moisture or 
heat without adequate ventilation.  Moisture penetration or heat buildup may 
result in product failure.

 

REDUCE GAIN AND SOURCE VOLUME TO MINIMUM LEVELS FOR INITIAL 

SYSTEM TUNING AND BEFORE CONNECTION TO AN AMPLIFIER.

 Ensure 

amplifier power is off before connecting RCA cables and follow proper system 
gain setting procedures. Failure to do so may result in damage to the amplifier 
and/or connected components. 

 CAUTION

 Package Contents:

Main Unit

Terminals

Accessories Required for 
Installation 

(not included)

:

Mounting Tabs

(detachable)

Ÿ

RCA Interconnects

Ÿ

18AWG Wire

Ÿ

In-line Fuse Holder w/1A fuse

Ÿ

Battery Ring Terminal

Ÿ

Wire Crimp Connectors

Ÿ

Grommets and Loom

Ÿ

Cable Ties 

Ÿ

Mounting Screws

PWR/SPK

GND

2

50

Содержание LinkDQ













Отзывы: