background image

7

Example-4: RCA Input from Portable Audio Player

RCA OUT

RCA IN

+12V

GND

REM OUT

linkRC 
(optional)

Top Panel Adjustments

Œ

Clipping Indicator:  This yellow 
LED indicates when the linkDQ’s 
output reaches maximum signal 
level before clipping (distortion) 
occurs. It will be dimly lit just 
before the onset of clipping, and 
full bright at clipping. Since the linkDQ can produce up to 10Vrms, 
its gain will usually be set well below this point while still 
maximizing your amplifier(s) input capability at minimum gain.



Gain Adjustment:  This adjustment is for matching the output of 
the linkDQ with the maximum unclipped signal provided by your 
source and the maximum input capability of your amplifier(s). 
Follow proper gain setting procedures to ensure optimum source 
volume range without clipping at any point within the signal chain 
while minimizing the ability to overdrive the system. Readjustment 
may be necessary after any changes to other level or EQ settings.

Ž

Parametric EQ:  This section provides adjustments for a single 
parametric EQ band with the tuning flexibility required for 
differences between vehicles, subwoofers and enclosures.



Boost:  Sets the amount of boost applied at the center 
frequency (Fc), adjustable up to +12dB. 



Frequency: Sets the center frequency (Fc) of the EQ band, 
adjustable from 30Hz to 80Hz.

Width: This switch selects the width (Q) of the EQ band 
between narrow and wide.

Note: 

 Portable devices such as smartphones typically have an output voltage of 

1Vrms or less. If using the device as the system’s volume control, it may be 
necessary to adjust gain vs. volume range for consistent auto turn-on behavior. 
For optimal signal range and convenient master volume control, the linkRC 
remote level controller is recommended (sold separately). 

Ž





Œ



50

50

Содержание LinkDQ













Отзывы: