2. Connect your Auditor
continued
Auditor 3R R-coil Connections
•
The R-coil connections are labelled 3+, 3-, 2+, 2-, 1+, 1-
•
Connect the R-coil blue wires to terminals marked 1+, 2+, 3+
•
Connect the R-coil white wires to terminals marked 1-, 2- , 3-
•
Connect the R-coil shields to the respective coil terminals
marked 1-, 2- , 3-
•
It is acceptable to use less than three R-coils.
Place R-coil connected to ... On cables connected to ...
1+ -1
P1
2+ -2
P2
3+ -3
P3
Need help with y
our ins
tallation
?
Our team is a
vailable fr
om 0900 to 17
00, Monda
y to Frida
y, S
ydne
y time.
Support phone:
02 8316 7
540
(+61 2 8316 7
540 from
overseas
)
Support: T o lodge a Support tick
et, please
visit our Support P
ortal at
ww
w.w
attw
atchers.
com.au/
support
Support
S0180
19 Quick
Start Guide
- A6M
2. Connect your Auditor
continued
WW0
18021 Quick
Start Guide
- A3R
Rogo
wski
Coil
2. Connect your Auditor
Three-Phase Voltage Connections
Use this configuration when there are multiple
phases present.
The voltage connections are labelled P1, P2, P3, N.
Connect voltage phases to P1, P2, and P3. Connect
neutral to N.
Use three-phase wiring tails if they were provided with
your Auditor.
Single-Phase Voltage Connections
Use this configuration when one phase is present.
The voltage connections are labelled P1, P2, P3, N.
Connect P1, P2 & P3 to the same phase.
Connect neutral to N.
Use single-phase wiring tails if they were provided
with your Auditor.
Auditor A3R
Rogo
wski Coil
Auditor 3R
Complete these f
our eas
y steps,
then start monit
oring your sit
e.
1.
Befor
e you
begin
2. Connect
your Audit
or
3. Use the
onboarding t
ool
4. V
alidate tha
t your ins
tallation is
corr
ect
1. Before you begin
Ensure you have the equipment
- See Auditor 3R checklist below. You’ll need an
internet connected smart device (e.g. smartphone, tablet, laptop) to configure
the Auditor and capture information about the installation. A marker is useful
for numbering Rogowski coil (R-coil) and cables during installation. You’ll need a
clamp meter for checking current measurements.
Check
- That you have 35mm wide space available on the DIN rail. If there is
not space, additional DIN rails may be mounted in the cabinet or an external
enclosure used. Ensure that R-coil can accommodate the cable size (i.e. cable
diameter fits within R-coil opening width).
Ensure there is a way to isolate the Auditor voltage inputs
- An existing or new
circuit breaker can be used depending on the regulations in your jurisdiction.
A breaker is not included in the Auditor package.
Auditor 3R hardware checklist:
• Auditor device - 2-unit wide DIN-mount
• Rogowski Coils - Supplied in a set of three
• Wiring tails - single-phase, 3-phase or both
• Connectors - green-coloured plastic plugs
ATTENTION:
Must be ins
talled by a lic
ensed electrician in ac
cor
dance
with standar
d electrical
safety r
egulations in
your jurisdiction.
ONL Y use this Audit
or with the R-c
oils it is supplied with.
This Audit
or is NOT
compa
tible with thir
d party coils
or split-cor
e Current T
ransf
ormers.
Version 1.
0_September 20
18
Rogowski Coil Direction
Install Rogowski coils (R-coils) such that:
• For grid monitoring: arrow is from grid
• For solar monitoring: arrow is from inverter
• For load monitoring: arrow is towards the load.
About the R-coils:
•
Only Wattwatchers-supplied R-coils are supported.
•
Only modified A3R Auditors can be used for R-coils
(because Auditors for use with split-core current
transformers have a different hardware configuration).
•
Wattwatchers R-coils are used when the measured
current is greater than 600A, up to 3,000A, or when the
aperture required is greater than 36mm in diameter.
• R-coils must be a loose fit around the conductor and the
two ends must join completely.
• Wattwatchers 3,000A R-Coils can be used to measure
200A or more.
