background image

3

1.0 Safety

This manual contains basic instructions that must be followed during 

the commissioning, operation, care and maintenance of the instrument. 

The safety protection provided by this equipment may be impaired if it 

is commissioned and/or used in a manner not described in this manual. 

Consequently, all responsible personnel must read this manual prior to 

working with this instrument.
In certain instances 

“Notices”

, or helpful hints, have been highlighted to 

give further clarification to the instructions. Refer to the 

Table of Contents

 

to easily find specific topics and to learn about unfamiliar terms.

This manual is intended to be used in conjunction 

with No. 28749 for more information on the 

connection and operation of the Air Sentinel.

2.2 Use in Explosive Environments Safety

In the interests of safety the operator must ensure the atmosphere 

where the instrument is located is safe from gases, vapors, dust or other 

flammable conditions whenever the instrument is opened for service or 

maintenance. At all other times the door must be kept closed with purge 

air connected the purge system operating with the all GREEN lamps lit 

indicating safe operation.

WARNING

!

If power is retained to the CLX-Ex after opening the enclosure 

door while NOT in bypass mode, immediately close the 

enclosure door and remove power to the instrument. Contact 

HF scientific service department for further instruction.

This symbol identifies hazards which, if not avoided, 

could result in death or serious injury. 
This symbol identifies hazards which, if not avoided, 

could result in minor or moderate injury or damage to 

the equipment.
This symbol identifies important information, 

practices or actions.

This pictorial alert you to the need read the manual, 

possibly at a different section.

This pictorial alerts you to electricity, electrocution 

and shock hazards.

1.1 Symbols Used in This Manual

WARNING

!

CAUTION

!

NOTICE

Содержание scientific CLX-Ex A28031

























Отзывы: