Watts scientific CLX-Ex A28031 Скачать руководство пользователя

Страница: 4 / 24

2.0 Overview

The CLX-Ex Online Chlorine Monitor allows for the reading of chlorine

levels of process water on-line. The CLX-Ex has been designed

to meet the design criteria specified by Standard Methods for the

Examination of Water and Wastewater (21th Edition) Method 4500-Cl

G. DPD Colorimetric Method. The CLX-Ex uses a 515nm LED as the

measurement light source.
This instrument has been designed to operate in explosive

atmospheres and meets the IECEx rating as stated in the

specifications. The instrument uses an approved purge/pressurization

controller called the Air Sentinel. Please refer to the companion manual

Cat. No. 28749 for all information on:

•  Operation of the Air Sentinel
•  Electrical power connections
•  Purge Air Connection

*Viton

is a trademark of The Chemours Company FC, LLC

Noryl

is a registered trademark of SABIC Global Technologies B.V.

2.1 Specifications

Measurement Range

0.00 – 10.00 mg/L (PPM)

Accuracy

±5% of reading or ±0.03 mg/L (PPM) whichever is greater for range of 0-6.0 mg/L(PPM) ±10% of reading from 6.01-10.00 mg/L (PPM)

Resolution

0.01 mg/L (PPM)

Cycle Time

Adjustable; 60 seconds to 10 minutes (600 seconds)

Display

Multi-Line Liquid Crystal Backlit Display

Alarms

One NO relay contact 120-240VAC 2A

Analog Output

Powered 4-20 mA, 600 Ω drive, isolated

Communications Port

Bi-directional RS-485 with Modbus

Water Pressure

Integral pressure regulator 0.34 bar (5.0 PSI) to 10.3 bar (150 PSI.)

Flow Rate to Waste

200 – 400 ml/min.

Operating Temperature

0°C – 55°C (32°F – 131°F)

Wetted Materials

PVC, Borosilicate Glass, Reslyn (FFKM), Viton

(FKM), Polypropylene, 316 Stainless Steel, Acetal, Noryl

, Silicone

Sample Temperature Range

0°C – 55°C (32°F – 131°F)

Power Supply

100 to 240VAC, 47-63 Hz, 250VA

Insulation Rating

Double Insulated, Pollution Degree 2, Overvoltage Category II

Environmental Conditions

Altitude up to 2000 meters
Up to 95% RH (non-condensing)

IECEx Hazloc Rating

Ex pxb IIC T4 Gb 0°C ≤ Ta ≤ 55°C

Compressed Air

Water and oil free, -40°F (-40°C) Dew Point, Particles <5u, ISA Grade Hydrocarbon Free. Full time clean dry air at 5.5 - 7 bar
(80-101.5 PSI) @35 SLPM (1.2 SCFM) @ 20°C (68°F) Max

Regulatory Compliance and Certifications

ETL listed to UL 61010-1 Issued May 11 2012 3rd Ed and ETL certified to CSA 22.2 No. 61010.1 issued May 11 2012
EN61326:2006

Shipping Weight

27.2 kg (60 lbs.) Reagents are Shipped Separately

Shipping Dimensions

93 cm X 62 cm X 32 cm (36½" X 24½" X 12½")

In addition this instrument has vortex cooling. This instrument will

automatically control a connected compressed air line to lower the

temperature of one of the reagents, allowing the reagent an operating

life of up to 3 months.
Every effort has been made to ensure the accuracy of this manual. Due

to the continuous development and improvement of all instrumentation,

there may be slight differences between this manual and the instrument

received. Therefore, no legal claims can be made against any

discrepancies herein.

Содержание scientific CLX-Ex A28031

























Результаты поиска

Содержание scientific CLX-Ex A28031

Отзывы:

Похожие инструкции для scientific CLX-Ex A28031

Бренды по названию

Популярные бренды

Watts scientific CLX-Ex A28031, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание scientific CLX-Ex A28031

Отзывы:

Похожие инструкции для scientific CLX-Ex A28031

Бренды по названию

Популярные бренды