Watts scientific CLX-Ex A28031 Скачать руководство пользователя

Страница: 16 / 24

8.13 4mA Adjustment

If the 4-20 mA setting is turned ON (8.1

Setting the 4-20

mA Output)

, the following two menus will appear. The first

menu outputs a constant 4 mA while allowing for a small

amount of adjustment. The adjustment can be made using

the



and



buttons. This adjustment will allow the operator to make

the CLX-Ex agree with a PLC or SCADA system. The adjustment limits

are ± 200 counts or about ± 0.2 mA.

This setting will be slightly different on each instrument as each CLX-Ex

will be factory set to 4.00mA. Press the



button when adjustments are

complete to save this setting and move on to the 20mA adjustment.

8.14 20mA Adjustment

This menu operates similar to the previous menu. This menu outputs a

constant 20 mA while allowing for a small amount of adjustment. The

adjustment can be made using the



and



buttons. The adjustment

limits are ± 1000 counts or about ± 1 mA.
This setting will be slightly different on each instrument as each CLX-Ex

will be factory set to 20.00mA.

When complete with the 20mA adjustment, press the



button to exit

to AUTO mode and save all configuration settings.

9.0 Additional Features and

Options

9.1 RS-485 Outputs

The CLX-Ex has the capability to operate in two different RS-485

modes. Included are a simple communication mode and Modbus

communications. Both modes will automatically configure and do not

require any changes or selections.

9.1.1 Simple Communication

The CLX-Ex can provide basic communications over simple programs

such as the Hilgraeve HyperTerminal that is included with most

Microsoft Windows packages. The user could also use Visual Basic

or other programs. The factory setting communication

parameters are 8 bits, no parity and 1 stop bit. These

can be changed in the Extended

CONFIG

menus

8.9

RS-485 Parameters

The master computer will send out:

• Byte #1 the attention character “

” in ASCII or

Hex

• Byte #2 the address of the CLX-Ex being queried
• Byte #3 & 4 CR LF or 0D 0A in hex

The CLX-Ex will respond with:

• The same attention character “

” in ASCII or 3A Hex

•  The address of the CLX-Ex
•  The Reading
•  The Unit (mg/L)

A sample communication would look like this:
(Master computer requesting a report

from address #1)

:1 CRLF

(CLX-Ex set to address #1 Response)

:001 0.0249mg/L

9.1.2 Modbus Communication

Modbus protocol communication is included with this instrument.

The Modbus address list is available from HF scientific or online at

www.hfscientiifc.com.

9.2 Remote Panel Meter (Catalog # 19609)

The remote panel meter allows for remote indication of the mg/L

reading using the 4-20 mA loop of the CLX-Ex. No external power is

required, as the meter is run off of the 4-20 mA source of the CLX-Ex.

Содержание scientific CLX-Ex A28031

























Результаты поиска

Содержание scientific CLX-Ex A28031

Отзывы:

Похожие инструкции для scientific CLX-Ex A28031

Бренды по названию

Популярные бренды

Watts scientific CLX-Ex A28031, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание scientific CLX-Ex A28031

Отзывы:

Похожие инструкции для scientific CLX-Ex A28031

Бренды по названию

Популярные бренды