manualshive.com logo in svg

Watt Stopper DT-200, Руководство по установке, Страница: 10 / 16

Поделиться
Скачать
Watt Stopper DT-200 Скачать руководство пользователя страница 10

SENSOR ADJUSTMENT

The sensors are factory preset to allow for quick installation in most applications. 

Verification of proper wiring or coverage, or customizing the sensor’s settings can 

be done using the following procedures. To make adjustments, open the Front Cover 

with a small screwdriver.

There is a 30 second warm-up period 

when power is first applied. 

Before making adjustments, make 

sure the office furniture is installed, 

lighting circuits are turned on, and the 

HVAC systems are in the overridden/

on position. VAV systems should be 

set to their highest airflow. Set the 

Logic Configuration and Time Delay 

to the desired settings. See “Logic 

Configuration Chart”, next page.

To Test Occupancy Sensors

1.  Ensure the Time Delay is set 

for

 Test Mode*

 using the “Test 

Mode/20 minutes” setting. (DIP 

switches 1, 2, & 3 are 

OFF

). 

2.  Ensure that the Light Level is at default (maximum). Press and hold the push-

button for 5 seconds or until the Green LED flashes rapidly. Wait 10 seconds 

for the flashing to stop.

3.  Ensure that the Ultrasonic Sensitivity trimpot is set to about 70%, clockwise.
4.  Remain still. The red and green LEDs should not flash. The lights should turn 

off after 5 seconds. (If not, see “Troubleshooting.”)

5.  Move around within the coverage area. The lights should come on. Adjust the 

Ultrasonic Sensitivity as necessary to provide the desired coverage (Green 

LED indicates activation from the ultrasonic sensor).

When testing and adjustment is complete, reset DIP Switches and Light Level to the 

desired settings, and replace the cover on the sensor.

*Test Mode 

is a temporary state that starts when you first set the sensor’s DIP 

switches for the “Test Mode/20 minutes” (switches 1, 2, 3 

OFF

). If you need to invoke 

the 

Test Mode 

and the DIP switches are already set for Test Mode/20 minutes, 

toggle DIP switch 1 

ON

 then back to the 

OFF

 position. This provides a 10 minute test 

period. During the test period, the Time Delay is only 5 seconds.

PIR Lens

Photocell

Ultrasonic 
Transducer 
Cones

PIR 
Activity LED

Ultrasonic 
Activity LED

Front Cover

Adjustments under the front cover

Press for Auto set
Hold 5 sec to disable 

Light Level

Button

Min

      

Max

Sensitivity

DIP

Switch

See

Back

Call 800.879.8585 for Technical Support

Содержание DT-200

















Отзывы:

Нет отзывов