Watt Stopper DT-200 Скачать руководство пользователя страница 1 | Manualshive

Страница: 1 / 16

Watt Stopper DT-200 Скачать руководство пользователя страница 1

DT-200

version 3

Dual Technology • Low Voltage

Occupancy Sensor

with Light Level, Isolated Relay and Manual On features

SPECIFICATIONS

Voltage  ............................................................................. 18-28VDC/VAC
Current Consumption ..................................................................... 25mA
Power Supply .................................................WattStopper Power Packs
Isolated Relay Rating ..................................................... 1A @30VDC/VAC
Operating Temperature ................................... 32° to 131°F (0° to 55°C)
Light Level One-Step Adjustment ...................................10FC to 200FC)
Time Delay Adjustment ...................................30 seconds to 30 minutes
  Walk-Through Mode ..................3 minutes if no activity after 30 sec.
  Test Mode ...................................................5 sec. or DIP switch reset
PIR Coverage (Typical) ................................................................ 1000 ft2
  Sensitivity Adjustment ....................High or Low (DIP switch setting)
Ultrasonic Coverage (Typical) .............................................. 800-1200 ft2
  Sensitivity Adjustment .................... Minimum to Maximum (trimpot)
Frequency ................................................................................. 40kHz

Ins
tallation Ins

tructions

Santa Clara, CA 95050

1
2
3
...
»

Содержание DT-200

















Отзывы:

Нет отзывов