manualshive.com logo in svg

Waters ACQUITY Arc System, Обзор и руководство по обслуживанию

Поделиться
Скачать
Waters ACQUITY Arc System Скачать руководство пользователя страница 8

Table of contents

General information .......................................................................................................ii

Copyright notice ..................................................................................................................................... ii

Trademarks............................................................................................................................................ ii

Customer comments.............................................................................................................................. ii

Contacting Waters .................................................................................................................................iii

Safety considerations.............................................................................................................................iii

Safety hazard symbol notice ...........................................................................................................iii
Considerations specific to the 30-cm Column Heater and 30-cm Column Heater/Cooler.............. iv
FCC radiation emissions notice...................................................................................................... iv
Electrical power safety notice ......................................................................................................... iv
Equipment misuse notice ............................................................................................................... iv
Safety advisories ............................................................................................................................. v

Operating the device.............................................................................................................................. v

Applicable symbols.......................................................................................................................... v
Audience and purpose.................................................................................................................... vi
Intended use of the 30-cm CH and 30-cm CHC............................................................................. vi
Calibrating ...................................................................................................................................... vi
Quality control................................................................................................................................. vi

EMC considerations.............................................................................................................................. vi

Canada spectrum management emissions notice..........................................................................vii
ISM classification: ISM group 1 class B..........................................................................................vii

EC authorized representative ...............................................................................................................vii

1 Overview....................................................................................................................11

1.1 Major components.........................................................................................................................13

1.2 Column heater...............................................................................................................................15

1.2.1 Column heater operation .....................................................................................................15

1.3 Column heater/cooler....................................................................................................................15

1.3.1 Column heater/cooler operation ..........................................................................................16

1.4 Column-selection valve kit option..................................................................................................16

1.4.1 Column-selection valve operation........................................................................................17

December 5, 2017, 715004751 Rev. C

Page viii

Содержание ACQUITY Arc System
















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды