manualshive.com logo in svg

Waters ACQUITY Arc System, Обзор и руководство по обслуживанию

Поделиться
Скачать
Waters ACQUITY Arc System Скачать руководство пользователя страница 7

Canada spectrum management emissions notice

This class A digital product apparatus complies with Canadian ICES-001.

Cet appareil numérique de la classe A est conforme à la norme NMB-001.

ISM classification: ISM group 1 class B

This classification has been assigned in accordance with CISPR 11 Industrial Scientific and
Medical (ISM) instrument requirements.

Group 1 products apply to intentionally generated and/or used conductively coupled radio-
frequency energy that is necessary for the internal functioning of the equipment.

Class B products are suitable for use in both commercial and residential locations and can be
directly connected to a low voltage, power-supply network.

EC authorized representative

Address

Waters Corporation
Stamford Avenue
Altrincham Road
Wilmslow SK9 4AX UK

Telephone

+44-161-946-2400

Fax

+44-161-946-2480

Contact

Quality manager

December 5, 2017, 715004751 Rev. C

Page vii

Содержание ACQUITY Arc System
















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды