manualshive.com logo in svg

Waters ACQUITY Arc System, Обзор и руководство по обслуживанию

Поделиться
Скачать
Waters ACQUITY Arc System Скачать руководство пользователя страница 6

Symbol

Definition

REF

Part number, catalog number

Audience and purpose

This guide is intended for use by individuals who operate and maintain the 30-cm Column Heater
(30-cm CH) or 30-cm Column Heater/Cooler (30-cm CHC).

Intended use of the 30-cm CH and 30-cm CHC

Waters designed the 30-cm CH and 30-cm CHC for use in liquid chromatography (LC)
applications. The 30-cm CH and 30-cm CHC are not intended for use with in vitro diagnostic
applications.

Calibrating

To calibrate LC systems, adopt acceptable calibration methods using at least five standards to
generate a standard curve. The concentration range for standards must include the entire range
of QC samples, typical specimens, and atypical specimens.

When calibrating mass spectrometers, consult the calibration section of the operator’s guide for
the instrument you are calibrating. In cases where an overview and maintenance guide, not an
operator’s guide, accompanies the instrument, consult the instrument’s online Help system for
calibration instructions.

Quality control

Routinely run three QC samples that represent subnormal, normal, and above-normal levels of a
compound. If sample trays are the same or very similar, vary the location of the QC samples in
the trays. Ensure that QC sample results fall within an acceptable range, and evaluate precision
from day to day and run to run. Data collected when QC samples are out of range might not be
valid. Do not report these data until you are certain that the instrument performs satisfactorily.

EMC considerations

December 5, 2017, 715004751 Rev. C

Page vi

Содержание ACQUITY Arc System
















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды