Waters ACQUITY Arc System Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 79

Waters ACQUITY Arc System Скачать руководство пользователя страница 2

General information

Copyright notice

© 2016 – 2017 WATERS CORPORATION. PRINTED IN THE UNITED STATES OF AMERICA
AND IN IRELAND. ALL RIGHTS RESERVED. THIS DOCUMENT OR PARTS THEREOF MAY
NOT BE REPRODUCED IN ANY FORM WITHOUT THE WRITTEN PERMISSION OF THE
PUBLISHER.

The information in this document is subject to change without notice and should not be construed
as a commitment by Waters Corporation. Waters Corporation assumes no responsibility for any
errors that may appear in this document. This document is believed to be complete and accurate
at the time of publication. In no event shall Waters Corporation be liable for incidental or
consequential damages in connection with, or arising from, its use. For the most recent revision
of this document, consult the Waters website (

).

Trademarks

ACQUITY

®

is a registered trademark of Waters Corporation.

ACQUITY Arc

®

is a registered trademark of Waters Corporation.

Empower

®

is a registered trademark of Waters Corporation.

MassLynx

®

is a registered trademark of Waters Corporation.

THE SCIENCE OF WHAT'S POSSIBLE

®

is a registered trademark of Waters Corporation.

TORX

®

is a registered trademark of Acument Intellectual Properties, LLC in the United States or

other countries.

Tygon

®

is a registered trademark of Saint-Gobain Performance Plastics Corporation.

Waters

®

is a registered trademark of Waters Corporation.

Waters Quality Parts

®

is a registered trademark of Waters Corporation.

All other trademarks are property of their respective owners.

Customer comments

Waters’ Technical Communications organization invites you to report any errors that you
encounter in this document or to suggest ideas for otherwise improving it. Help us better
understand what you expect from our documentation so that we can continuously improve its
accuracy and usability.

December 5, 2017, 715004751 Rev. C

Page ii

«
1
2
3
4
...
»

Содержание ACQUITY Arc System
















































































Отзывы:

Нет отзывов