background image

GUARANTEE

Warranty Period 

This warranty is not transferable and covers the actuator only. 
See Honda Engine manual for details of engine warranty.
Waterra (UK) Limited warrants that under normal use and correct maintenance it will replace at no
cost to the customer any defects in material or workmanship for a period of 1 year from date of
purchase as follows: 

6 months:

All parts and labour

1 year: 

All parts and labour subject to completion of 100 hour or 6 month service. 

Normal use and maintenance must follow the guidance in this manual. Warranty claims must be

accompanied by: 

x

A copy of the actuator usage record card

x

A copy of a service certificate for the first 100 hour or 6 monthly service by a Waterra approved
servicing agency (for claims between 6 months and 1 year) 

Warranty Exclusions 

x

Repairs required as a result of incorrect maintenance, accidental damage or use outside the
recommended pumping depth parameters

x

Repairs required as a result of non-approved third parties maintaining the product or any
unapproved modifications

x

Repairs required on any unit which has been loaned or rented to third parties by the purchaser

x

Normal maintenance requirements, such as lubrication and tightening screws, etc. 

x

Clamping strap (except for material faults)

See our Terms & Conditions which can be supplied on request.
This does not affect your Statutory Rights.

For Warranty conditions outside the UK and Ireland, refer to local Waterra dealer.

STORAGE

Proper storage preparation is essential to keep the PowerPack trouble free.  The following steps
should be carried out when storing the PowerPack:

x

Clean all exterior surfaces.  Most base materials are aluminium, but if paintwork is damaged, it is
recommended that this is touched in with a paint stick. 

x

Wipe ratchet clean with a lightly oiled cloth.

x

Drain fuel. 

x

Retain packing carton

 in case equipment needs to be shipped. It will be needed for transit by

courier for servicing.

w

 PP1

21

Содержание Waterra PowerPack PP1























Отзывы: