Waterous CP-4 Скачать руководство пользователя

Страница: 39 / 41

39 | 41

Testing After Installation

Use the illustration and instructions to adjust the

packing after installing the pump into the apparatus.

Note:

Certain parts have been removed from the

illustration to provide a clear view of the

equipment being tested.

1 Operate the pump at its maximum intended

pressure for 10 minutes.

2 Observe the drip rate. Optimal leakage is 10

to 120 drops per minute. Maintaining this rate

facilitates the cooling of the packing.

3 If the drip rate is too high, turn off the

pump and gradually tighten the gland nuts,

alternating between them to make sure that

the gland stays level.

4 Operate the pump at its maximum intended

pressure for 2 minutes. Observe the drip rate,

then repeat the previous step until leakage is

within the optimal range.

5 Repeat the process with the packing housing

at the other end of the pump.

6 Make sure that you perform all tests required

by the National Fire Protection Association.

Содержание CP-4










































Результаты поиска

Содержание CP-4

Отзывы:

Похожие инструкции для CP-4

Бренды по названию

Популярные бренды

Waterous CP-4, Инструкции по капитальному ремонту

Результаты поиска

Содержание CP-4

Отзывы:

Похожие инструкции для CP-4

Бренды по названию

Популярные бренды