Waterous CM Series Скачать руководство пользователя страница 59

Страница: 59 / 61

F-1031, Section 4212

Page 59 of 61

Transfer Valve Removal / Installation for Reciprocating Actuator (Prior to 2000)

NOTE: The transfer valve only needs to be removed and
disassembled if it needs to be repaired.

There is a repair kit available for replacing the seals in the transfer
valve.

1. Remove the three 1/2-13 x 1 in. hex head screws that attach

the transfer valve cover to the pump body. Do not remove
the four 5/16-18 x 3/4 in. socket head screws.

2. Use the two jacking screw holes to remove the transfer

valve from the pump body.

See page 49 for correct orientation of sector gear and arm.

See page 50 for connecting top mounted actuator to valve
operating arm.

Jacking Screw Hole

Socket Head Screw,

5/16-18 x 3/4 in. (4)

Hex Head Screw,

1/2-13 x 1 in. (3)

Transfer Valve Cover

Top Mounted

Transfer Valve

Bottom Mounted

Transfer Valve

Jacking Screw Hole

IL1294

Содержание CM Series






























































Результаты поиска

Содержание CM Series

Отзывы:

Похожие инструкции для CM Series

Бренды по названию

Популярные бренды

Waterous CM Series, Инструкции по капитальному ремонту

Результаты поиска

Содержание CM Series

Отзывы:

Похожие инструкции для CM Series

Бренды по названию

Популярные бренды