Waterous CM Series Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 61

background image

F-1031, Section 4212

Page 2 of 61

WARNING

WARNING

WARNING

WARNING

WARNING

WARNING

Safety Information

Please read through the safety information and operating instructions carefully before using your Waterous Fire Pump.

WARNING

Packing Gland and Pump Body Temperature Hazard. May result in
serious burns.

Heat is dissipated through the cross-section of the packing, transferring
the heat to the packing gland and pump body.

WARNING

Scalding Water Hazard. May result in serious burns.

When operating the pump, be sure to open at least one discharge valve
slightly to prevent the pump from overheating. If the pump runs for a few
minutes completely closed, it may heat the water enough to scald

some•

one when the valve is opened. Overheating can damage the packing,
seals and other pump parts. If the apparatus builder has installed a by-
pass system or other provision designed to prevent overheating, opening a
discharge valve may be unnecessary.

WARNING

Rotating Parts Hazard or Unexpected Truck Movement. May result in

seri•

ous personal injury or death.

Stop the engine, set parking brake and chock the wheels before going under
the truck to adjust packing or to check packing gland temperature.

WARNING

Pressure Hazard. May result in personal injury.

Prior to connection or removal of hoses, caps or other closures with pump
intake or pump discharge connections, relieve pressure by opening drains
or bleeder valves. Bleeder valves should also be used while filling a hose
connected to an intake with water.

WARNING

Unexpected Truck Movement. May result in serious personal injury
or death.

Failure to properly shift transmission in accordance to the transmission
operating instructions may result in unexpected truck movement which
may result in serious personal injury or death.

WARNING

Death or serious personal injury might occur if proper operating procedures
are not followed. The pump operator, as well as individuals connecting
supply or discharge hoses to the apparatus must be familiar with these
pump operating instructions as well as other operating instructions and
manuals for the apparatus, water hydraulics and component limitation.

«
1
2
3
4
...
»

Содержание CM Series






























































Отзывы:

Нет отзывов

Похожие инструкции для CM Series

Бренд: Ebsray Страницы: 12

Бренд: VARISCO Страницы: 16

Бренд: Water Worker Страницы: 24

Бренд: Raymarine Страницы: 24

SunCentric Series

Бренд: Dankoff Solar Страницы: 11

PROFESSIONAL 5965-01

Бренд: Simer Страницы: 19

Бренд: Larzep Страницы: 14

Бренд: Walrus Pump Страницы: 12

JABSCO 18670 Series

Бренд: Xylem Страницы: 16

Бренд: Beckett Страницы: 2

Бренд: Bock Water heaters Страницы: 36

Бренд: SAER Elettropompe Страницы: 20

Бренд: Macon Страницы: 24

Бренд: Galletti Страницы: 40

Бренд: Wayne Страницы: 8

FLEXFLO A2P Series

Бренд: Blue-White industries Страницы: 16

Бренд: Nakayama Страницы: 33

ARO PF20 B Series

Бренд: Ingersoll-Rand Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды