Waterite BLACKMAXX RB8, Руководство оператора

Страница: 8 / 26

8
!
TEST THAT THE PRE-TREATMENT SYSTEM IS DELIVERING RO FEED WATER TO
NECESSARY SPECIFICATIONS BEFORE PLUMBING THE RO SYSTEM ONLINE.
!
ALWAYS ALLOW NEW SOFTENING SYSTEMS INSTALLED TO PRE-TREAT AN RO SYSTEM
TO START ON THE BACKWASH/REGENERATION/RINSE CYCLE. OPERATE THE SOFTENER
OFF-LINE UNTIL WATER RUNS CLEAR BEFORE USING IT TO PROVIDE RO FEED WATER.
THIS PROCEDURE ALSO APPLIES TO NEW RESIN BED INSTALLATIONS. COLOUR THROW
FROM NEW RESIN BEDS MAY DAMAGE OR FOUL RO MEMBRANES.
!
WATERITE DOES NOT RECOMMEND THE USE OF A GRANULAR CARBON CARTRIDGE IN
THE PRE-TREATMENT FILTER HOUSINGS SUPPLIED, FOR THE PRIMARY REDUCTION OF
CHLORINE. IT WILL REQUIRE REPLACEMENT TOO OFTEN, LIMIT FLOW RATES AND
LIKELY LEAD TO CHLORINE BREAKTHROUGH TO THE MEMBRANE ELEMENT. WE
RECOMMEND THAT THIS HOUSING BE RESERVED FOR 5-MICRON OR 1-MICRON
SEDIMENT CARTRIDGES, FOR THE REDUCTION OF SUSPENDED PARTICULATE.
Step 3. Plan your water system
1. Using a pressure storage tank and pressure switch
Nominal rates of water production for BlackMaxx™ RB8 systems are, at maximum (feed water
@<500 TDS and 25 degrees Celsius recovery maximum 15%/membrane pH 7.5):
RB820K 20000GPD 13.8 USGPM 52.2 LPM 0.9 L/s 75.7 M3/d
RB830K 30000GPD 20.8 USGPM 78.7 LPM 1.3L/s 113.3 M3/d
RB840K 40000GPD 27.7 USGPM 104.4 LPM 1.6 L/s 151.4 M3/d
RB860K 60000GPD 41.5 USGPM 156.6 LPM 2.51L/s 227.1 M3/d
RB880K 80000GPD 55.4USGPM 209 LPM 3.3 L/s 302.8 M3/d
RB8100K 100000GPD 69.4 USGPM 262.7 LPM 4.4 L/s 378.5 M3/d
RB8120K 120000GPD 83.3 USGPM 315.3 LPM 5.3 L/s 454.2 M3/d
RB8150K 150000GPD 104.2 USGPM 394.4 LPM 6.6 L/s 587.8 M3/d
RB8180K 180000GPD 125 USGPM 473.2 LPM 7.9 L/s 681.3 M3/d
RB8210K 210000GPD 145.8 USGPM 551.9 LPM 9.9 L/s 794.9 M3/d
RB8240K 240000GPD 166.6 USGPM 630.6 LPM 10.5 L/s 908.4 M3/d
For many commercial, industrial or municipal requirements, this rate of production will be insufficient
in periods of peak usage, though over 24 hours the necessary production will be produced. It will
be necessary for you to provide product water storage in a non-pressurized tank from which you
may re-pressurize the water for delivery to your equipment or plumbing system. Sizing of the tank
is at the discretion of the end user; however, it should be sized to minimize the starting of the system
at less than 2 times per hour. See appendix for Membrane Temperature Correction Factors.
!
IF THE SYSTEM IS CONNECTED DIRECTLY TO A PRESSURE TANK, MAKE SURE THAT A
CHECK VALVE IS INSTALLED ON THE PRODUCT WATER LINE BETWEEN THE MACHINE
OUTLET AND THE PLUMBING SYSTEM PRESSURE SWITCH, TO ELIMINATE
BACKPRESSURE ON THE MEMBRANE(S). FAILURE TO DO SO WILL CAUSE PERMANENT
DAMAGE TO THE RO MEMBRANE(S).