WaterGroup 6200 SXT Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 41

background image

37

Trouble Shooting Guide

Problem

Possible Solutions

1. CONDITIONER DELIVERS HARD WATER

A. Bypass valve is open
B. No salt in brine tank
C. Injector or screen plugged
D. Insufficient water flowing into brine tank
E. Hot water tank hardness

F. Leak at distributor tube
G. Internal valve leak

H. Flow meter jammed
I. Flow meter cable disconnected or not

plugged into meter cap

J. Improper programming

A. Close bypass valve
B. Add salt to brine tank and maintain salt level above water level
C. Replace injectors and screen
D. Check brine tank fill time and clean brine line flow tank control if

plugged

E.  Make sure distributor tube is not cracked. Check O ring and tube pilot
F.  Make sure distributor tube is not cracked. Check O ring and tube pilot
G. Replace seals and spacers and/or piston
H. Remove obstruction from flow meter
I. Check meter cable connection to timer and meter cap

J.  Reprogram the control to the proper regeneration type, inlet water

hardness, capacity or flow meter size.

2. CONDITIONER FAILS TO REGENERATE

A. Electrical service to unit has been

interrupted

B. Timer is not operating properly
C. Defective valve drive motor
D. Improper programming

A. Assure permanent electrical service (check fuse, plug, chain or switch)
B. Replace timer
C. Replace drive motor
D. Check programming and reset as needed

3. UNIT USES TOO MUCH SALT

A. Improper salt setting
B. Excessive water in brine tank
C. Improper programming

A. Check salt usage and salt setting
B. See #7
C. Check programming and reset as needed

4. LOSS OF WATER PRESSURE

A. Iron build-up in line to water conditioner
B. Iron build-up in water conditioner

C. Inlet of control plugged due to foreign

material broken loose from pipes by
recent work done on plumbing system.

A. Clean line to water conditioner

B. Clean control and add resin cleaner to resin bed. Increase frequency

of regeneration

C. Remove piston and clean control

5. LOSS OF RESIN THROUGH DRAIN LINE

A. Air in water system

B. Drain line flow control is too large

A. Assure that well system has proper air eliminator control. Check for dry

well condition.

B. Ensure drain line flow control is sized

6. IRON IN CONDITIONED WATER

A. Fouled resin bed

B. Iron content exceeds recommended

parameters

A. Check backwash, brine draw and brine tank fill. Increase frequency of

regeneration. Increase backwash time.

B. Add iron removal filter system

«
...
36
37
38
39
40
...
»

Содержание 6200 SXT










































Отзывы:

Нет отзывов

Похожие инструкции для 6200 SXT

Бренд: Rain Bird Страницы: 48

Бренд: Danfoss Страницы: 24

Бренд: GARAN Страницы: 8

Бренд: Gamma Vacuum Страницы: 25

Бренд: Gamma Страницы: 28

Бренд: Omegalink Страницы: 2

Бренд: Olsberg Страницы: 68

Бренд: Valcom Страницы: 6

eTracer ET4415BND

Бренд: Epsolar Страницы: 44

Бренд: Graco Страницы: 166

IntelliCross TouchFree Kit

Бренд: Novax Страницы: 3

Бренд: Daikin Страницы: 19

Бренд: SMC Networks Страницы: 15

Бренд: Znshine Solar Страницы: 16

Phase Matrix PXI-1420

Бренд: National Instruments Страницы: 38

Бренд: WAGO Страницы: 134

Бренд: GAC Страницы: 9

Бренд: ALLEN & HEATH Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды