background image

pg 06

GENERAL SAFETY RULES

1.  The installation of the Waterco LED Pool Light should be carried out in accordance to the 

safety instructions of swimming pools especially Standard HD 60364-7-702:2010, Install & 
protection output circuit in accordance with AS/NZS61558.2.6, AS/NZS 3000:2007 or as 
amended and the specific instructions for each facility.

2.  The rules enforced on accident prevention should be carefully followed.

3.  Any modification of the Waterco LED Pool Light requires the prior consent of the 

manufacturer.

4.  Original replacement parts and accessories authorized by the manufacturer ensure a high 

level of safety.

5.  The manufacturer accepts no liability for the damage and injuries caused by unauthorised 

replacement parts and accessories.

6.  During operation, some parts of the Waterco LED Pool Light are subject to dangerous 

electric voltage.

7.  Work may only be performed on the Waterco LED Pool Light or on the equipment connected 

to it after disconnecting from the mains power.

8.  The user should make sure that assembly and maintenance tasks are carried out by 

qualified authorised persons and that these persons have first carefully read the owner 
manual.

9.  The operating safety of the Waterco LED Pool Light is only guaranteed if the owner manual 

instructions are correctly followed.

10.  In the event of defective operation or fault, contact the manufacturer’s Technical Support 

Department or its nearest Authorised Agent.

11.  If the supply cord is damaged, it must be replaced by the manufacturer or its service agent 

or a similarly qualified person.

12. This appliance is not intended for use by persons (including children) with reduced 

physical, sensory or mental capabilities, or lack of experience and knowledge, unless they 
have been given supervision or instruction concerning use of the appliance by a person 
responsible for their safety.

WARRANTY

BriteStream LED lights are covered by a comprehensive 2 years warranty. Please refer to the
Waterco Warranty Booklet for further details.

Waterco Britestream LED Fibreglass Niche Pool Lights MK5

Содержание Britestream MK5









Отзывы: