background image

WATERMAZE SERIES   

OPERATOR’S MANUAL

  

7

WB  •  8.913-984.0-L

WARNING: The gas line must be 
installed  by qualified person-
nel only. It must be checked for 
leaks before installing the WATER 
MAZE. All gas piping must com-
ply with local and national fuel 
gas codes. 

Connect the main gas line to the 1" 
or 1-1/2" line on the rear panel of the 

WATER MAZE

. This will be labeled 

“Natural Gas Only” or “L.P.  Gas Only” depending on the 
machine you purchase. Connect the vent line to the 1" 
vent pipe on the rear panel of the 

WATER MAZE

 (see 

figures 1-3).

CAUTION: This vent pipe must be vented to the at-
mosphere. 

Electrical:

The 

WATER MAZE

 requires 230 volts single phase. Re-

fer to the serial plate for proper voltage and amp require-
ments for your machine. All electrical lines must be tested 
with a voltage meter for proper voltage before connect-
ing to the 

WATER MAZE

NOTE: If 208V single phase 

is the only electrical source available, the step down 
transformer must be changed to a 208/120V transformer  
(#6-60011) or a buck boost transformer must be used 
to increase the voltage.

DANGER: All electrical lines must 
be installed by qualified person-
nel only. All installations must 
be electrically grounded and 
conform to all local and national 
electrical codes. Water Maze is 
ETL listed. 

The electrical connection for the 

 

WATER MAZE 

is located on the 

rear panel conduit box using a 1/2" knock-out. Electrical 
conduit must be run all the way to the connection point 
in accordance with local codes.

Fresh Water:

During initial start up, we recommend using fresh water in 
the wastewater tank. Fill to mark indicated on sight tube 
and remove garden hose. Connect the garden hose to the 

 

WATER MAZE

 at the female connector located on the 3 

point level controller. Open valve partially so back pres-
sure doesn't fill up sight glass tube.

Wastewater:

Wastewater is drawn directly into the evaporator using 
the air pump supplied. A 20 mesh stainless steel filter
protects the pump from debris. The connection between 
the above ground waste water tank and the machine is 
made by using a 3/4"  I.D. supply hose with common 

WARNING

GAS LINE MUST 

BE INSTALLED BY 

QUALIFIED 

PERSONNEL ONLY.

Control Rod:

Automatic wastewater control set points on the 3 Point 
Level Controller turns the wastewater air pump on and 
off to control the water level inside the evaporator. The 
controller also shuts burner off if water level gets to low.

Temperature Control:

Dual, manual reset, and high temperature controls 
monitor the internal temperature of the evaporator. If the 
exhaust or water temperatures become too high (225°F) 
the system shuts down. The temperature is usually in 
the 180° to 190° range.

Regulator Venting:

A pressure regulator gas vent is provided. The gas vent 
needs to be plumbed to the atmosphere. If the gas  
regulator fails, the gas is automatically vented out-
side, preventing a gas buildup in the location of the 

 

WATER MAZE

. This must be vented to comply with  

local and/or national codes.

Demister Box:

The demister box contains screens inside that prevent 
large water droplets from going up the stack (screen 
hole size is 3/16").

INSTALLATION

Location:

Locate the 

WATER MAZE  

evaporator on a level con-

crete surface in a room that is well ventilated. Protect the 
machine from damaging environment such as wind, rain 
and freezing temperatures. Leveling feet are provided 
with all evaporators.

CAUTION: For natural gas, air ventilation should 
be located near the ceiling. For liquid propane, air 
ventilation should be located near the floor.

Gas:

The 

WATER MAZE

 evaporator is available for operation 

in natural gas or liquid propane.

CAUTION: There are major differences in the adjust-
ments of the evaporators. Do not try to operate the 
machine using the wrong gas. 

The one inch (1") gas supply line on the WB-25, and 
WB-50 and (one and one half inch (1-1/2") on the  
WB-120) must have a minimum of 2 psig and a maxi-
mum of 10 psig and be of adequate size to supply the 
necessary volume for proper burner operation. The high/
low gas switches require between 12-60 water column 
inches. There must be a main gas shut-off valve (not pro-
vided) in the gas supply line located next to the 

WATER 

MAZE

 which can be used as an emergency shut off for 

repair or maintenance purposes.

HAZARDOUS 

VOLTAGE. CAN  

SHOCK, BURN OR 

CAUSE DEATH. 

DANGER

Содержание WB Series



























































Отзывы: