background image

 4  Responsibility for Operation or Damage

The responsibility for operating the device lies exclusively with the owner or user if said 

device is incorrectly serviced, maintained or altered by persons not employed by an 

authorised dealer or if the device is used in a manner contrary to its specified purpose.

The unit has to be maintained and operated in accordance with this user manual. 

Wassermann Dental-Maschinen GmbH is not responsible for damage arising from the 

nonobservance

 of these instructions.

Warranty and responsibility provisions contained in the sales and supply conditions of 

Wassermann Dental-Maschinen GmbH are not extended by these instructions.

 5  Application

The Wapo-Ex is used for scalding up to 4 half-caps and up to 6 caps for polymerisation. A 

divider in the trough creates two separate chambers. You can also scald small items using

a hand spray.

Only use the device for this type of application.

 6  Before Starting

 6.1 

Transport

Before transporting the unit, ensure that it has been unplugged from the power socket. 

Make sure that it is packed correctly in order to avoid accidental damage.

Be sure to check for any transport damage when unpacking the goods. Note down 

any damage if found.

6

Содержание WAPO-Ex

























Отзывы: