background image

 

INTRODUCTION 

Congratulations on your purchase of a winch.  We design and build winches to strict 

specifications  and  with  proper  use  and  maintenance  should  bring  you  years  of 

satisfying service.  

 

WARNING

 - 

Read, study and follow all instructions before operating this 

device.    Failure  to  heed  these  instructions  may  result  in  personal  injury 

and/or property damage. 

 

Your  winch  can  develop  tremendous  pulling  forces  and  if  used  unsafely  or 

improperly could result in property damage, serious injury or death.  Throughout 

this  manual  you  will find  the  following  symbols for  caution,  warning  and  danger.  

Pay particular attention to the notes preceded by these symbols as they are written 

for your safety. Ultimately, safe operation of this device rests with you, the operator. 

 

Indicates a potentially hazardous situation which, if not avoided, may result in 
minor or moderate injury.  This  notation is also used to alert against unsafe 
practices. 

 

Indicates a potentially hazardous situation which, if not avoided 
could result in death or serious injury. 

 

1

 

 CAUTION

 

 

WARNING

 

Содержание 8000




















Отзывы: