5 September 2019
All dimensions are in mm
Copyright
5
Due to continued product improvement, Warmington Ind LTD reserves the right to change product specifications without prior notification.
Your purchase of the Warmington traditional fire gas burner (included in the price of the firebox) comes with multiple options for lighting/ heat
settings. The most affordable option is the ‘SG’ option, which is a manual start, manual adjustment option, working much like a barbeque.
Alternatively, Warmington offers several electronic options
-
‘ON
-
OFF’ with a switch at the wall to operate the fire, or ‘ON
-
OFF
-
HIGH
-
LOW’
with two settings for heat output. Furthermore, a fully adjustable electronic ‘EG’ option is available, supplied with remote control.
OPERATION OF A WARMINGTON SG GAS FIRE (MANUAL START)
To light:
•
Open
the front cover by pulling it outwards
•
Push in the ignition control switch and hold in the
‘PILOT’
position for 5
-
10 seconds until you can
hear the gas come through the pipe, making sure the ignition switch is pressed in firmly.
•
To strike the igniter, turn anti clockwise to the
*STAR
position (
w
ith the ignition switch still firmly
pressed in
)
until you hear the pilot ignite with a ‘click’.
Repeat this process 2 or 3 times if
necessary.
•
Once the pilot flame is lit, hold this position for 3
-
5 seconds, then gently let the ignition switch out
and set the flame control to high.
It may take a few seconds for the burner to light all the way
across.
•
Once the flame is established, adjust to the desired setting and close the cover.
To shut down:
•
Open the cover by pulling it outwards.
•
Turn the control ignition switch to
‘PILOT’
and the flame bed will extinguish. Pilot light may be left on and the pilot flame will still
burn.
•
To fully extinguish, turn to the
‘OFF’
position before closing the cover.
OPERATION OF A WARMINGTON EG ELECTRONIC GAS FIRE
AS SHOWN FROM THE FRONT OF THE BURNER
This control panel is located on the bottom left hand side
of your Warmington decorative gas fire.
Press and release the power button. This will start the
electronic spark and the power LED will be on
permanently . The pilot will ignite first and once this is on,
it will ignite the main burner. Pressing and releasing the
power button again will switch off the appliance.
When the appliance is turned on again, the gas fire will resume the previous flame and fan settings, unless the appliance was switched off
due to power failure. In the circumstance of a power failure the Remote Control System will return to the default settings which is a low
flame and the fan turned off.
If the gas fails to light, the appliance it will go into lock out mode, after trying to ignite for 1 minute (approx.). In lock out mode the power
LED will remain illuminated. To start the appliance again, press and release the power button twice after the gas supply resumes.
REMOTE CONTROL
Your remote control has all the features of the control receiver situated on the front panel of the
burner.
By pressing the timer button, the power LED will start flashing and after 30 minutes the appliance
will shut off automatically. By pressing the timer button again within the 30 minute period, this will
reset the timer and the power LED will stop flashing.
Press and hold the
+
button to increase the main burner flame.
Press and hold the
-
button to decrease the main burner Flame.
By holding the
+
or
-
flame button for up to 10
-
15 seconds, this will increase or decrease the
main burner flame to it’s max or min.
The Warmington decorative gas fire has a 3 Speed Fan and its operated independent from the
main burner. This is done by pressing and releasing the fan
+
or
–
button will increase or
decrease the fan speed. The LED on the front panel will indicate the fan settings at low, medium,
or high speed. Pressing and releasing of the button will lower the speed until the fan is turned off.
