WarmFlow Agentis B Series Скачать руководство пользователя страница 118 | Manualshive

Страница: 118 / 136

WarmFlow Agentis B Series Скачать руководство пользователя страница 118

Page

117

13 COMBINATION BOILER FAULT FINDING

WARNING: The Combination Boiler fault finding tables (Central Heating and Hot Water) are
to only be used by competent and suitably qualified engineers. It may be necessary to
check live terminals inside the control panel. Extreme care should be taken when doing
so.

13.1 Error codes displayed on the LCD.

Combination Boilers are fitted with diagnostic functions that monitor the correct function of
certain control systems within the appliance.
Error codes are displayed on the LCD, a list of Error codes, their possible causes and
corrective actions are detailed below.

Code Description

Possible Cause (s)

Corrective Action (s)

E01

Burner Lockout

No fuel supply to burner, air in fuel lines

Burner fault

Consult Service Engineer

E02

High Limit

Air Lock in boiler, displaced NTC
Temperature Sensor, circulation problem

Consult Service Engineer

E04

Low System
Pressure

System not topped up after pressure loss
after bleeding radiators etc.

Leak in heating system

Check system pressure, see
Section 1.3, 1.4 & 1.5 then, check
corrosion inhibitor concentration.

E05

Boiler NTC Error Boiler Flow NTC Temperature Sensor

short circuit or disconnected

Consult Service Engineer

E06

DHW Flow NTC
Error

DHW Flow NTC Temperature Sensor
short circuit or disconnected

Consult Service Engineer

E11* Tank Limit

Displaced Tank NTC Temperature
Sensor Probe

Consult Service Engineer

E12

Tank Control
NTC Error

Tank Control NTC Temperature Sensor
short circuit or disconnected

Consult Service Engineer

E15* CH Return NTC

Error

CH Return NTC Temperature Sensor
short circuit or disconnected

Consult Service Engineer

E22

Flash Data
Corrupted

PCB Fault

Consult Service Engineer

E31

Remote Control
Communication
Error

Damaged Remote Control cable

Remote Control Fault

Consult Service Engineer

E32

MMI - Control
PCB Error (On
Remote Control)

Damaged cable in control panel

PCB Fault

Consult Service Engineer

E46

System
Pressure
Sensor Error

System Pressure Sensor disconnected

System Pressure Sensor Fault

Consult Service Engineer

E48

High System
Pressure

Filling Loop left connected, and open

Insufficient system expansion capacity

Consult Service Engineer

E62

MMI - Control
PCB Error (On
Boiler)

Damaged cable in control panel

PCB Fault

Consult Service Engineer

9

«
...
116
117
118
119
120
...
»

Содержание Agentis B Series









































































































































Отзывы:

Нет отзывов